Few questions on props and other bits

Starts at the flywheel, ends at the hubs, any problems along them lines, ask your questions here.
User avatar
Gilly_SJ
Got muddy boots
Got muddy boots
Posts: 55
Joined: Sun Feb 28, 2016 7:36 pm

Few questions on props and other bits

Post by Gilly_SJ » Sat Mar 19, 2016 6:03 pm

Basically my SJ has started vibrating heavily under drive. Goes when you back off so I'm assuming is a UJ. Quick look under and it would appear my rear diff has moved and is aiming upwards slightly. Could be normal but looks off to me

Image

Image

It also looks like the extension bit may be over extended as the rubber boots in front and rear won't reach over the greased internal part.

Image

Next one, my starter keeps sticking as if the battery hasn't enough juice but will then go. On closer inspection the starter only us one bolt in as the adaptor plate for the engine doesn't quite line up! Anyone else had this? Looks like I'm going to need to remove the engine or drill the hole out a bit so I can get a bolt in.

sorry for the long post but I'm trying to get this as mechanically sound as possible!

User avatar
andyrew
SCUK is my life
SCUK is my life
Posts: 1820
Joined: Fri Jul 31, 2009 12:39 am

Re: Few questions on props and other bits

Post by andyrew » Sat Mar 19, 2016 6:48 pm

:BS:

Its hard to tell from the pic but if your diff is pointing
Up then you either havent got any spring preches or they
Have been moved possibly after being returned from spring
Over axle.
Andys Rusty Suzuki Emporium

User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: Few questions on props and other bits

Post by ROBBIE » Sat Mar 19, 2016 6:56 pm

From the pic it looks like, as said, no perches
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Few questions on props and other bits

Post by Jordi » Sat Mar 19, 2016 6:57 pm

The prop boot isn't too much to worry about. Common thing if it's on lift springs or has had the axles moved forwards and backwards for extra tyre clearance.

As Andy say more photos of the back axle to get a better look and a pic where it mounts to the spring.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
Gilly_SJ
Got muddy boots
Got muddy boots
Posts: 55
Joined: Sun Feb 28, 2016 7:36 pm

Re: Few questions on props and other bits

Post by Gilly_SJ » Sat Mar 19, 2016 7:47 pm

Image

That's the axle mount, also not sure why it's wet and it did smell of transmission fluid :argh:

Oh joy

User avatar
Gilly_SJ
Got muddy boots
Got muddy boots
Posts: 55
Joined: Sun Feb 28, 2016 7:36 pm

Re: Few questions on props and other bits

Post by Gilly_SJ » Sat Mar 19, 2016 7:49 pm

On a plus note it has Astra rear shocks and a shock bar so that saves me a job

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Few questions on props and other bits

Post by Jordi » Sat Mar 19, 2016 8:00 pm

No spring perch. And is there only 1 u bolt on there?

Not sure how you get a oil leak there either without the axle case being worn through.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
Gilly_SJ
Got muddy boots
Got muddy boots
Posts: 55
Joined: Sun Feb 28, 2016 7:36 pm

Re: Few questions on props and other bits

Post by Gilly_SJ » Sat Mar 19, 2016 8:07 pm

I'm not convinced it isn't cracked but hey ho, I take it Spring perches are a fab item not something I can buy

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Few questions on props and other bits

Post by Jordi » Sat Mar 19, 2016 8:14 pm

Nah you can buy them. Not sure where in the UK though.

Low Range Off Road do them.

Easy enough to make but getting all the geometry right is a bit harder when you weld them back together.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
andyrew
SCUK is my life
SCUK is my life
Posts: 1820
Joined: Fri Jul 31, 2009 12:39 am

Re: Few questions on props and other bits

Post by andyrew » Sat Mar 19, 2016 10:15 pm

Scary stuff that. Seems the p.o was a bit of a hack.

Some 50mm (i think) box section should do the job.
Basically. Angle either end. Semi circle out the middle.
Or flat plate with little truss triangles. Just google it and theres
Loads of different ways to go.

Pinion angle is important and i think the degrees are
On here somewhere. If it were me id bolt everthing up on the car set the angle and clamp it in place by tightening the ubolts.
Then tack the new perches, remove and weld up. On sjs the springs
Sag unevenly so if you do this method id measure the distance from the chassis leg and the top of the leaf spring
Nearest the perch to make sure its level. If that makes sense?
Andys Rusty Suzuki Emporium

Post Reply