fitting new seats? welding up arches? Painting your SJ? post your queries here
-
Phillips321
- Got muddy boots

- Posts: 72
- Joined: Fri Apr 15, 2016 5:40 pm
- Location: Gloucestershire
Post
by Phillips321 » Tue Apr 26, 2016 5:18 pm
Hi guys,
I need 3 of the popper type clips:
and 1 of the pin type clips:
Any idea where i can get them from?
Many thanks
-
zook123
- SCUK Addict

- Posts: 948
- Joined: Sun Apr 20, 2008 10:48 pm
- Location: Shepton Mallet
Post
by zook123 » Tue Apr 26, 2016 5:42 pm
Wow! The ones for my Jimny are nearly £8 each!!!
2002 Jimny O2 Ragtop
Safari Snorkel, Freewheeling Hub Conversion
Diff Breathers, G/Box and T/Box Breathers, 2in Suspension Lift
HD Recovery Points and Winch Plate
Kuhmo KL71 MT / Goodyear Wrangler AT
Wessex 4X4 Reponse - WE411
wessex4x4response.org.uk
-
donkeychomp
- I spend far too much time on here

- Posts: 3582
- Joined: Thu Aug 18, 2011 3:49 pm
- Location: Shepperton, Middx
Post
by donkeychomp » Tue Apr 26, 2016 8:20 pm
Camping shops sell them and you'll need a tool if you want to put new ones on your soft top. ThinkI got 100 and the tool for a fiver.
If it ticks over...leave it
-
Phillips321
- Got muddy boots

- Posts: 72
- Joined: Fri Apr 15, 2016 5:40 pm
- Location: Gloucestershire
Post
by Phillips321 » Wed Apr 27, 2016 11:06 am
Thanks, have just ordered a set.
-
twiss
- SCUK Computer Wizard

- Posts: 6111
- Joined: Mon Nov 08, 2010 2:28 pm
- Location: Brighton, UK
-
Contact:
Post
by twiss » Mon May 02, 2016 8:02 am
They look better than the last ones I used.... they were rivet on type and came off eventually
Twiss
'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410
"If brute force doesn't fix your problem, you aren't using enough of it."
-
Phillips321
- Got muddy boots

- Posts: 72
- Joined: Fri Apr 15, 2016 5:40 pm
- Location: Gloucestershire
Post
by Phillips321 » Tue May 03, 2016 7:52 am
twiss wrote:They look better than the last ones I used.... they were rivet on type and came off eventually
However the right most lug on the tailgate is going to be a pain. The thread has snapped off in the hole which i can't get to the back of. I'm planning to drill it out and see if i can put the new one in there.
-
SherwoodNash
- Winching along now

- Posts: 731
- Joined: Sat Aug 09, 2014 11:05 am
Post
by SherwoodNash » Tue May 03, 2016 8:25 am
Phillips321 wrote:twiss wrote:They look better than the last ones I used.... they were rivet on type and came off eventually
However the right most lug on the tailgate is going to be a pain. The thread has snapped off in the hole which i can't get to the back of. I'm planning to drill it out and see if i can put the new one in there.
These Easy Out 3-25mm Bergen 2584 sets are mighty useful for working on your SJ.
-
Phillips321
- Got muddy boots

- Posts: 72
- Joined: Fri Apr 15, 2016 5:40 pm
- Location: Gloucestershire
Post
by Phillips321 » Tue May 03, 2016 8:41 am
SherwoodNash wrote:

These Easy Out 3-25mm Bergen 2584 sets are mighty useful for working on your SJ.
I've not seen them before, how do they work? You drill the old thread and then use the other bit to make new thread?
-
ROBBIE
- I spend far too much time on here

- Posts: 4562
- Joined: Tue Sep 09, 2008 6:32 pm
- Location: Dorset or stuck
Post
by ROBBIE » Tue May 03, 2016 9:00 am
They are for removing snapped bolts, drill down the middle of bolt and screw one in and hopefully will turn the bolt out. You will need to drill and re tap the thread in the door
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good