Mot question
Mot question
everything works on my sj been on the mot website but as you well know that one of my sj front wheel arch has rusted but its not that bad u can see through it though it seems that its the only probelm ! so was wondering if this would fail it. as im temped to put it in for a mot !
Sj410Q- Spacers, Bucket seats, Su carb , Mot and Tax
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Mot question
It'll fail. Mine had a rust hole in the front of the bonnet.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
turbo-tom
- I spend far too much time on here
- Posts: 4478
- Joined: Fri Jun 25, 2010 9:29 pm
- Location: West Sussex
Re: Mot question
yep my mot will get his pry bar and boom hill will poke it throught it make it bit bigger put yellow mark with chalk around it and boom fail , the joys of working in a garage to know these things 
Tom 
Ford Fiesta ST
Ford Fiesta ST
Re: Mot question
if its non structural then you can put a bit of duct tape over the hole to get it through an mot.
as long as there's no sharp edges and its not close to anything structural it should pass.
as long as there's no sharp edges and its not close to anything structural it should pass.
If at First You Don’t Succeed Skydiving Is Not for You
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: Mot question
The place where I get mine done the have a roll of duct take set aside for just that.
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Mot question
Depends where you go. Mine were fully detached for a while.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Re: Mot question
If it's within 12" of a body or seatbelt mount it will fail, if not it will be fine.
-
suzukisteve
- Suzuki Guru
- Posts: 1344
- Joined: Sat Feb 04, 2012 10:07 am
- Location: Christchurch, Dorset
Re: Mot question
technically speaking a tester is not allowed to remove anything. so for for example if gaffer tape etc is covering a hole he or she can't remove it to inspect whats underneath.
however, that said, there is always the piece of mind knowing you've done a job properly and that the mot tester will pass it.
if it were me id just do the work so its done done and solid. that way you know its worthy.
however, that said, there is always the piece of mind knowing you've done a job properly and that the mot tester will pass it.
if it were me id just do the work so its done done and solid. that way you know its worthy.
pickle power!
Re: Mot question
but he's allowed to prod, poke, hit and scrape with a MOT toolsuzukisteve wrote:technically speaking a tester is not allowed to remove anything. so for for example if gaffer tape etc is covering a hole he or she can't remove it to inspect whats underneath.
It wouldn't take much to put one of these through some gaffer tape
and he's perfectly within his rights to poke through it -
suzukisteve
- Suzuki Guru
- Posts: 1344
- Joined: Sat Feb 04, 2012 10:07 am
- Location: Christchurch, Dorset
Re: Mot question
you are quite right my good sir. I used to do mots for a couple years with the old man. while testing for rust you are 'supposed' to lightly 'tap' or scrape any area that is in your opinion rusty.
However you know as well as I do that most mot testers will hit a muddy 4x4 pretty hard on a test due to the the nature of the vehicle.
its far better to get the work done before it gets any worse. and seein as you dont actually drive it on the road yet ollie, do the work first so you dont waste 50 quid on a test.
thats what I reckon anyways
However you know as well as I do that most mot testers will hit a muddy 4x4 pretty hard on a test due to the the nature of the vehicle.
its far better to get the work done before it gets any worse. and seein as you dont actually drive it on the road yet ollie, do the work first so you dont waste 50 quid on a test.
thats what I reckon anyways
pickle power!