Splitting steering box / arm ball joint

Post your questions about your suspension and steering problems here!
Post Reply
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Splitting steering box / arm ball joint

Post by Jordi » Sat May 25, 2013 9:31 pm

I'll give that a try in the morning, i'll be ready to go before machine marts open anyway.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
mike harris
SCUK is my life
SCUK is my life
Posts: 1828
Joined: Sat Jan 08, 2011 8:30 pm
Location: hascombe Surrey

Re: Splitting steering box / arm ball joint

Post by mike harris » Sat May 25, 2013 9:46 pm

Hammer
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Splitting steering box / arm ball joint

Post by Jordi » Sat May 25, 2013 9:53 pm

Hammer wasn't doing anything.

I'll have a mess about with it tomorrow. Failing that i'll get a splitter to do it.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
twiss
SCUK Computer Wizard
SCUK Computer Wizard
Posts: 6110
Joined: Mon Nov 08, 2010 2:28 pm
Location: Birkirkara, Malta
Contact:
Contact twiss

Re: Splitting steering box / arm ball joint

Post by twiss » Fri May 31, 2013 10:53 am

I'm pretty sure I took the turret nut thing off, put a regular nut on it, then used a big metal pole from the top through the engine bay. Whacked it with le sledgehammer until it came loose, then took the nut off and removed...
Twiss

'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410

"If brute force doesn't fix your problem, you aren't using enough of it."
Top
User avatar
will
Got muddy boots
Got muddy boots
Posts: 20
Joined: Sat Feb 16, 2013 11:17 pm
Location: Northampton

Re: Splitting steering box / arm ball joint

Post by will » Fri May 31, 2013 11:13 am

A good squirt of wd40 and using 2 hammers hit on either side of the arm where the bolt goes through. That should be enough to shift it.
Top
User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Splitting steering box / arm ball joint

Post by turbo-tom » Sat Jun 01, 2013 1:23 am

Mine came about with Ferris's method and thats the method I always use if not I use Wills method and it works second time! :)
Tom :)

Ford Fiesta ST :D
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Splitting steering box / arm ball joint

Post by Jordi » Sat Jun 01, 2013 1:27 am

I bought a ball joint splitter. Only £10 and did the job no fuss.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
Post Reply

Return to “SJ series Suspension and Steering”