The little bolt bit that stops the gear lever spinning round

Starts at the flywheel, ends at the hubs, any problems along them lines, ask your questions here.
Post Reply
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

The little bolt bit that stops the gear lever spinning round

Post by Jordi » Tue May 28, 2013 12:19 am

You all know the one. It bolts in from the back of the box.

Where can i get a one? There was a mod on here somwhere to sort it but i can't find it.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
Ricky-410
Engaged 4wd low
Engaged 4wd low
Posts: 205
Joined: Sun Oct 07, 2012 11:45 pm
Location: West Cumbria

Re: The little bolt bit that stops the gear lever spinning r

Post by Ricky-410 » Tue May 28, 2013 1:01 am

i just got a normal bolt and ran the end in a bench grinder until it fit in the gap, works great. no slop at all

User avatar
dan_2k_uk
I spend far too much time on here
I spend far too much time on here
Posts: 4924
Joined: Tue May 06, 2008 5:19 pm
Location: Swindon, Wiltshire

Re: The little bolt bit that stops the gear lever spinning r

Post by dan_2k_uk » Tue May 28, 2013 6:33 am

I did the same as Ricky but used an angle grinder and a drill.
Image
Janspeed manifold, LWB Vit vented discs and calipers

Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.

User avatar
ianedwards
SCUK Addict
SCUK Addict
Posts: 878
Joined: Thu Sep 15, 2011 8:23 pm
Location: Brecon Powys

Re: The little bolt bit that stops the gear lever spinning r

Post by ianedwards » Tue May 28, 2013 2:15 pm

id recomend using a bolt, and doing as the guys say.

i bought a kit from mountain goat performance, came with a new bolt, and replacment bushes for the gear stick and transfer box,

im going there on way home, do you want me to get the bolt out and get the dimensions for you to copy.

Ian
Cheers

Ian. :)

1987 Suzuki SJ413 KJA - Fixed + Modified in my own way

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: The little bolt bit that stops the gear lever spinning r

Post by Jordi » Tue May 28, 2013 3:03 pm

That would be brill bud.

May even buy that kit and do the lot.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: The little bolt bit that stops the gear lever spinning r

Post by Jordi » Wed May 29, 2013 4:51 am

If they are correct it means i managed to find part numbers all by myself. Gonna give Suzuki a ring later on. Don't think they're open at 04:50.

01935-08006 Bolt
08321-21083 Spring Washer
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: The little bolt bit that stops the gear lever spinning r

Post by Jordi » Wed May 29, 2013 11:23 am

My suzuki dealer didn't recognise those part numbers but have ordered me the correct parts off this diagram. About £3 i think he said.
image.jpg
image.jpg (101.7 KiB) Viewed 5454 times
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
ianedwards
SCUK Addict
SCUK Addict
Posts: 878
Joined: Thu Sep 15, 2011 8:23 pm
Location: Brecon Powys

Re: The little bolt bit that stops the gear lever spinning r

Post by ianedwards » Wed May 29, 2013 3:44 pm

Sorry, I got called back into work on the way home yesterday. I didn't have a chance to go up there but it sounds like you have sorted it out. :thumbup:

Ian
Cheers

Ian. :)

1987 Suzuki SJ413 KJA - Fixed + Modified in my own way

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: The little bolt bit that stops the gear lever spinning r

Post by Jordi » Wed May 29, 2013 3:46 pm

All sorted cheers. Will be at my local Suzuki dealer tomorrow.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

Post Reply