Project Bodge

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
User avatar
ferris
Suzuki Guru
Suzuki Guru
Posts: 1226
Joined: Thu Jul 23, 2009 3:55 pm
Location: Bristol

Re: Project Bodge

Post by ferris » Sun Feb 17, 2013 10:37 am

Finally treated my SJ to a new air filter, as the old one was starting to look a bit dirty. Got a second hand K&N off ebay, and as i'm sure we are all aware a K&N is a guaranteed extra 20bhp :guns: .
Image
86 SJ413 tin top, 1.6 8v, SU carb, YJ spring conversion, virtual lift, 33x12.5x15 KL71's, rocklobster, rear discs, power steering.

User avatar
andyrew
SCUK is my life
SCUK is my life
Posts: 1820
Joined: Fri Jul 31, 2009 12:39 am

Re: Project Bodge

Post by andyrew » Sun Feb 17, 2013 11:08 am

Got one of those in mine, I like it seems a little more responsive but only a little . Also supposedly never needs to be replaced.
Andys Rusty Suzuki Emporium

User avatar
ferris
Suzuki Guru
Suzuki Guru
Posts: 1226
Joined: Thu Jul 23, 2009 3:55 pm
Location: Bristol

Re: Project Bodge

Post by ferris » Sun Feb 17, 2013 11:34 am

I'v noticed a small differance, but i think that is becuse my old filter was covered in mud :lol: .
86 SJ413 tin top, 1.6 8v, SU carb, YJ spring conversion, virtual lift, 33x12.5x15 KL71's, rocklobster, rear discs, power steering.

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Project Bodge

Post by turbo-tom » Mon Feb 18, 2013 6:43 pm

let me know how many miles per gallon you get with this filter! it might not change but my old man put one in his p38 and it was going about 15mpg rather then about 19mpg it might not effect it but it did in the rangie :lol:
Tom :)

Ford Fiesta ST :D

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Project Bodge

Post by Jordi » Mon Feb 18, 2013 6:46 pm

Another boy racer mod. Lol.

Is it washable?

Cheers
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
ferris
Suzuki Guru
Suzuki Guru
Posts: 1226
Joined: Thu Jul 23, 2009 3:55 pm
Location: Bristol

Re: Project Bodge

Post by ferris » Mon Feb 18, 2013 7:29 pm

I'v no idea how many mpg's i was getting before :lol: . My speedo is so far out its impossible to work it out. I hope it doesn't get worse, i allready spend a outrageos amount on fuel.

You can wash it, but you then need to put some special pink K&N oil on it after...or whatever oil you've got lying around in the garage.

Once a boy racer, allways a boy racer :hahaha: .
86 SJ413 tin top, 1.6 8v, SU carb, YJ spring conversion, virtual lift, 33x12.5x15 KL71's, rocklobster, rear discs, power steering.

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Project Bodge

Post by Jordi » Mon Feb 18, 2013 7:39 pm

It's like James May said. Its easier and more fun to drive a small low powered car to its limit than a ferrari.

I don't spend a huge amount on fuel but my MPG is appalling. Very low 20s.

Once i get the rock lobster and 1600 in i'll work it out again.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
ferris
Suzuki Guru
Suzuki Guru
Posts: 1226
Joined: Thu Jul 23, 2009 3:55 pm
Location: Bristol

Re: Project Bodge

Post by ferris » Mon Jun 24, 2013 9:35 pm

Who would of thought changing the gearstick would be such a pain in the arse :lol:

Picked up a gear stick off Scottie yesterday as mine had no gator on it. So thought i would change the gearbox oil at the same time. So emptyed out the old watery crap and a couple of the gear teeth came out with it :roll: . I had a spare gear box in the shed so i thought i would change it. So after wrestling with the old box for a hour finally got the bastard out. Then it turns out the bearing in the fly wheel is completely destroyed :pissed: (I didn't even know there was a bearing in the fly wheel)

So once again the SJ is in a hundred pieces on the drive untill i can get hold of the parts.

Image
Image
Image
86 SJ413 tin top, 1.6 8v, SU carb, YJ spring conversion, virtual lift, 33x12.5x15 KL71's, rocklobster, rear discs, power steering.

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Project Bodge

Post by Jordi » Mon Jun 24, 2013 9:47 pm

You are kidding me?

Hope you can get it sorted for Wiltshire.

And that bearing is the pilot bearing, holds / supports the gearbox input shaft.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Project Bodge

Post by turbo-tom » Mon Jun 24, 2013 9:51 pm

Not good!, im sure you will get it sorted intime! :thumbup:
Tom :)

Ford Fiesta ST :D

Post Reply