rockwatt manifold and su hif44 carb pipe work help needed
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: rockwatt manifold and su hif44 carb pipe work help neede
Think there was one that went to the old carb which gets blanked?
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: rockwatt manifold and su hif44 carb pipe work help neede
Is it blanked Dan? I think i just effectively joined the old carb feed and return together to complete the "circuit".dan_2k_uk wrote:Think there was one that went to the old carb which gets blanked?
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: rockwatt manifold and su hif44 carb pipe work help neede
Do u mean the return being the hose that goes to the bottom of the thermostat housing?
Re: rockwatt manifold and su hif44 carb pipe work help neede
These are the water pipes im not sure about
- Attachments
-
- 20130626_085611.jpg (2.66 MiB) Viewed 5739 times
Re: rockwatt manifold and su hif44 carb pipe work help neede
These
- Attachments
-
- 20130626_085611.jpg (2.66 MiB) Viewed 5738 times
Re: rockwatt manifold and su hif44 carb pipe work help neede
This is how I understand it
The far right goes to the bottom of the inlet manifold under the thermostat
The fat one is the bottom rad hose
The left one at the bottom goes to the heater valve closest to the brake res pot
The left top one is the one in the previous pic which doesnt go to anything?
The far right goes to the bottom of the inlet manifold under the thermostat
The fat one is the bottom rad hose
The left one at the bottom goes to the heater valve closest to the brake res pot
The left top one is the one in the previous pic which doesnt go to anything?
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: rockwatt manifold and su hif44 carb pipe work help neede
I will look at mine later if you are still stuck. I cant remember and I am using the 1.3 water rail not the 1.6 one which might have an extra hose position.
Where is the other hose from the heater matrix going?
Where is the other hose from the heater matrix going?
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Re: rockwatt manifold and su hif44 carb pipe work help neede
Im still stuck on this, the bottom left one im not sure where it goes, any help welcome. If I can get it sorted I still might make wagtail
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: rockwatt manifold and su hif44 carb pipe work help neede
The top left in that photo is just blanked with a bolt and a jubilee clip on mine.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: rockwatt manifold and su hif44 carb pipe work help neede
The hose from the Heater valve goes to the manifold.
The rest are marked here
The rest are marked here
- Attachments
-
- Untitled.jpg (932 KiB) Viewed 5701 times
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.