Palmers samurai tin top build

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
Post Reply
User avatar
palmer
Got muddy boots
Got muddy boots
Posts: 91
Joined: Sun Apr 15, 2012 7:11 pm
Location: bury st edmunds, suffolk

Palmers samurai tin top build

Post by palmer » Sun Jul 07, 2013 9:48 am

Hey all well this is my first build thread for my Suzuki samurai 413vsb commercial, she is a 1991 h-reg. There won't be any major changes to her she needs a few parts of rust sorting mainly around the windscreen and the rear arches are starting to rust but apart from that she is in good nick. She needs some tidying up inside nothing major, I am going to replace the front seats as the drivers is pretty knackered, the previous owner removed the stickers from both sides of the truck but didn't do a very good job so that's first on the list. The engine runs without fault and it still has the original carb on it which I know are crap but while it is running well I might as well leave it alone. I also want to get some news tyres for her I want something that's good on the road but can handle a bit of green laneing and off road sites, I have heard that kumho kl71 are good for this, anyway here are some pictures I will take a lot more and go into detail a bit further tomorrow when I go to work, cheers Palmer :guns:
Attachments
IMG_20130629_103434.jpg
IMG_20130629_103434.jpg (814.08 KiB) Viewed 8610 times
IMG_20130629_103420.jpg
IMG_20130629_103420.jpg (676.22 KiB) Viewed 8610 times
IMG_20130629_103408.jpg
IMG_20130629_103408.jpg (732.07 KiB) Viewed 8610 times
As you can see the drivers seat is knackered.
As you can see the drivers seat is knackered.
IMG_20130629_103447.jpg (734.33 KiB) Viewed 8610 times
The tappets are a bit noisy so will have to adjust them as well.
The tappets are a bit noisy so will have to adjust them as well.
IMG_20130629_093703.jpg (946.09 KiB) Viewed 8610 times
1.3 engine
Webber carb
Roll cage
Spoa
32 mm wheelspacers
Extended brake lines
31" Bronco Grizzerly Claws

MONSTER ENERGY DISCO KILLER!!

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Palmers samurai tin top build

Post by turbo-tom » Sun Jul 07, 2013 10:02 am

Grab you self a can of this guy I use it all the time cracking stuff! Wipe it all over the sticky areas then 2mins later wipe it over with a squeedgy/ credit card

http://www.elitecarcare.co.uk/autosmart ... litres.php

Petrol kinda works but it avaperates have of the time
Tom :)

Ford Fiesta ST :D

User avatar
palmer
Got muddy boots
Got muddy boots
Posts: 91
Joined: Sun Apr 15, 2012 7:11 pm
Location: bury st edmunds, suffolk

Re: Palmers samurai tin top build

Post by palmer » Sun Jul 07, 2013 10:41 am

turbo-tom wrote:Grab you self a can of this guy I use it all the time cracking stuff! Wipe it all over the sticky areas then 2mins later wipe it over with a squeedgy/ credit card

http://www.elitecarcare.co.uk/autosmart ... litres.php

Petrol kinda works but it avaperates have of the time
Cheers tom think I might invest in a can :lol:
1.3 engine
Webber carb
Roll cage
Spoa
32 mm wheelspacers
Extended brake lines
31" Bronco Grizzerly Claws

MONSTER ENERGY DISCO KILLER!!

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Palmers samurai tin top build

Post by turbo-tom » Sun Jul 07, 2013 12:53 pm

Yeah you might need some! my disco was the same and it had batternburg all over it exactly the same stuff the old bill used!
Tom :)

Ford Fiesta ST :D

User avatar
Darrell
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2988
Joined: Wed Feb 23, 2011 7:54 pm
Location: south oxfordshire
Contact:

Re: Palmers samurai tin top build

Post by Darrell » Sun Jul 07, 2013 5:27 pm

This stuff is supposed to be good, but I've not used it so can't say.
Available at most motorist shops so may be worth a shot before ordering the big stuff.


Click Here for Ebay Listing
2005-GV 1600se, "Hell" What do I know!

Richie
Engaged 4wd low
Engaged 4wd low
Posts: 192
Joined: Fri Nov 09, 2012 6:23 pm

Re: Palmers samurai tin top build

Post by Richie » Sun Jul 07, 2013 8:30 pm

Nice truck m8. Are u using it atm?

User avatar
palmer
Got muddy boots
Got muddy boots
Posts: 91
Joined: Sun Apr 15, 2012 7:11 pm
Location: bury st edmunds, suffolk

Re: Palmers samurai tin top build

Post by palmer » Sun Jul 07, 2013 8:51 pm

Richie wrote:Nice truck m8. Are u using it atm?
Hello mate long time no speak, I have it down the pit atm its just been m.o.t'd for the year so just tax and insurance and she is ready to rock and roll. she needs a bit of tidying up but nothing major and some new rubber beneath her feet.
1.3 engine
Webber carb
Roll cage
Spoa
32 mm wheelspacers
Extended brake lines
31" Bronco Grizzerly Claws

MONSTER ENERGY DISCO KILLER!!

User avatar
palmer
Got muddy boots
Got muddy boots
Posts: 91
Joined: Sun Apr 15, 2012 7:11 pm
Location: bury st edmunds, suffolk

Re: Palmers samurai tin top build

Post by palmer » Mon Jul 08, 2013 7:13 pm

Some more pics of her now, this afternoon at work found myself a bottle of thinners so thought i would have a go at removing the marks left from the stickers. It made a pretty good job of it and looks a lot better now. I thought i would make a start on cleaning the inside a bit, just made a start removing the rear bench and seat belts. It has a sort of plastic flooring which i am going to remove to check for rust and give it a good clean out. What would be the best way to deal with the rust below the windscreen? There is also a small red light just to the left of the steering wheel what is this?, is does not light up or anything.
Attachments
Not made much of a start but a start it is, also on the plus side found the 5 speed badge that was missing off the back.
Not made much of a start but a start it is, also on the plus side found the 5 speed badge that was missing off the back.
IMG_20130708_161154.jpg (743.52 KiB) Viewed 8541 times
And after.
And after.
IMG_20130708_155219.jpg (675.33 KiB) Viewed 8541 times
Before.
Before.
IMG_20130708_153220.jpg (560.97 KiB) Viewed 8541 times
IMG_20130708_153242.jpg
IMG_20130708_153242.jpg (814.64 KiB) Viewed 8541 times
IMG_20130708_153306.jpg
IMG_20130708_153306.jpg (632.59 KiB) Viewed 8541 times
What is this???
What is this???
IMG_20130708_153334.jpg (1.09 MiB) Viewed 8541 times
Someone has tryed putting filler in it which i don't think has helped
Someone has tryed putting filler in it which i don't think has helped
IMG_20130708_153209.jpg (845.51 KiB) Viewed 8541 times
1.3 engine
Webber carb
Roll cage
Spoa
32 mm wheelspacers
Extended brake lines
31" Bronco Grizzerly Claws

MONSTER ENERGY DISCO KILLER!!

User avatar
donkeychomp
I spend far too much time on here
I spend far too much time on here
Posts: 3582
Joined: Thu Aug 18, 2011 3:49 pm
Location: Shepperton, Middx

Re: Palmers samurai tin top build

Post by donkeychomp » Mon Jul 08, 2013 10:05 pm

The light could be for a lot or reasons, it's an after market addition so maybe an old alarm or some such. Have a look and see where the wires go (if there are any!)
If it ticks over...leave it

Post Reply