Kiwizook's resto
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Kiwizook's resto
The left hand 2 are for a 1.3 carb. I always have the lower round one left over.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Re: Kiwizook's resto
The two on the right look like EGR gaskets and the lower one could be for the thermostat housing.
2006 Jimny JLX+ 1.3 VVT
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
Re: Kiwizook's resto
turns out the round gasket is for the hose conector piece on the water rail on the intake manifold. have rebuilt my head, and it's ready to go back on. am almost done cleaning the block, so it's almost ready to paint. also I'm just about done painting all the bits for the engine, just need to buy some rings and big end bearings, fit them, and put everything back together. hopefully this weekend will be fine, so I can finish painting the chassis. am slowly getting there now 
It's not a question of how much you spend on your suzuki, but when your money will run out
Re: Kiwizook's resto
had a good day today, worked for 5 and a half hours, then got round to painting my front part of the chassis
also masked the engine block ready to sprayed next week, cool green tape 
- Pic_0824_201.jpg (778.42 KiB) Viewed 5159 times
- Pic_0824_200.jpg (674.88 KiB) Viewed 5159 times
- Pic_0824_202.jpg (345.75 KiB) Viewed 5159 times
It's not a question of how much you spend on your suzuki, but when your money will run out
-
donkeychomp
- I spend far too much time on here
- Posts: 3582
- Joined: Thu Aug 18, 2011 3:49 pm
- Location: Shepperton, Middx
Re: Kiwizook's resto
That chassis looks very impressive, nicely done there.
If it ticks over...leave it
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Kiwizook's resto
Top work bud, the chassis is looking spot on.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: Kiwizook's resto
thanks for all the kind comments guys.
ordered the piston rings and big end bearings, bring it on rebuild!
ordered the piston rings and big end bearings, bring it on rebuild!
It's not a question of how much you spend on your suzuki, but when your money will run out
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Kiwizook's resto
That engine is gonna like brand new!
Bet you can't wait to get it all rebuilt and fire it up.
Bet you can't wait to get it all rebuilt and fire it up.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: Kiwizook's resto
oh yes, "new" (read different second hand, in good nick, skimmed) rebuilt head, all new gaskets and belts, new frost plugs, new waterpump, newly painted, new bearings and rings, su hs2 carb conversion. she's gonna be a goodun 
just need some help puting everything back together properly, but a friend has offered his help, getting so excited now
just need some help puting everything back together properly, but a friend has offered his help, getting so excited now
It's not a question of how much you spend on your suzuki, but when your money will run out