king pin bearings have gone in my 410 axle
Re: king pin bearings have gone in my 410 axle
Thats the exact same swivel seal that I fitted to mine last month the felt bit is a seperate item you need to order two halves for either side. When you fit the rubber swivel seal soak it in hot water first as this will make it easier to get over the end of the axle.
1991 Suzuki Samurai, 1.6 16v MPFI, 4.16:1 Transfer Box, Rear Lockrite Diff, SPOA, YJ Springs, 31X10.5x15 Maxxis Trepador Tyres on BK Wheels, 8000LB Winch and Bumper, PAS Conversion
- Ladaman
- Suzuki Guru
- Posts: 1090
- Joined: Thu Sep 08, 2011 10:56 pm
- Location: Huddersfield, W. Yorkshire
- Contact:
Re: king pin bearings have gone in my 410 axle
I'd say it is the same.
You just need to carefully pull away the felt wiper and you should be able to re use it
You just need to carefully pull away the felt wiper and you should be able to re use it
YouTube
Ignis Sport 1.5 16V; Jimny gearbox, 410 transfer box; 5.125:1 Vitara diffs; rear Lockright, Rob Storr full float rear axle, rear discs, YJ springs, virtual lift, 31" Grizzly Claws, beadlock rims, +50mm LR arches, LED rear lights, LED roof spots, bucket seats, Luke harnesses, internal cage
Ignis Sport 1.5 16V; Jimny gearbox, 410 transfer box; 5.125:1 Vitara diffs; rear Lockright, Rob Storr full float rear axle, rear discs, YJ springs, virtual lift, 31" Grizzly Claws, beadlock rims, +50mm LR arches, LED rear lights, LED roof spots, bucket seats, Luke harnesses, internal cage
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: king pin bearings have gone in my 410 axle
Ok chears mate where do I get the felt bits from chears for the advice mate
If they are cheap I might get some New ones but if I can.reuse it I.might chears
If they are cheap I might get some New ones but if I can.reuse it I.might chears
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Re: king pin bearings have gone in my 410 axle
Jimnybits thats who I had mine from but as ladaman says you may be able to pull them apart and reuse them give it a go
1991 Suzuki Samurai, 1.6 16v MPFI, 4.16:1 Transfer Box, Rear Lockrite Diff, SPOA, YJ Springs, 31X10.5x15 Maxxis Trepador Tyres on BK Wheels, 8000LB Winch and Bumper, PAS Conversion
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: king pin bearings have gone in my 410 axle
Ok ideal iwill have a go in a minute chears
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: king pin bearings have gone in my 410 axle
Right is this ok to be used
- Attachments
-
- IMAG0384.jpg (1.1 MiB) Viewed 6695 times
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Re: king pin bearings have gone in my 410 axle
It should be ok if you close up that tear and fit it above centre then it wont stop you fitting it so that you can get it all built up then order some new ones. The new ones can then be split and fitted when you get them just make sure you get the split above centre
1991 Suzuki Samurai, 1.6 16v MPFI, 4.16:1 Transfer Box, Rear Lockrite Diff, SPOA, YJ Springs, 31X10.5x15 Maxxis Trepador Tyres on BK Wheels, 8000LB Winch and Bumper, PAS Conversion
- Ladaman
- Suzuki Guru
- Posts: 1090
- Joined: Thu Sep 08, 2011 10:56 pm
- Location: Huddersfield, W. Yorkshire
- Contact:
Re: king pin bearings have gone in my 410 axle
It should be OK. Note the slots aren't equally spaced so it will on go on in one of two positions. So as gp7186 says put the tear to the top.
When I did my front axle recently, I didn't need to cut the seal or wiper. You can ease them on if you get the first bit right into the joint of the casing and knuckle.
Good luck.
When I did my front axle recently, I didn't need to cut the seal or wiper. You can ease them on if you get the first bit right into the joint of the casing and knuckle.
Good luck.
YouTube
Ignis Sport 1.5 16V; Jimny gearbox, 410 transfer box; 5.125:1 Vitara diffs; rear Lockright, Rob Storr full float rear axle, rear discs, YJ springs, virtual lift, 31" Grizzly Claws, beadlock rims, +50mm LR arches, LED rear lights, LED roof spots, bucket seats, Luke harnesses, internal cage
Ignis Sport 1.5 16V; Jimny gearbox, 410 transfer box; 5.125:1 Vitara diffs; rear Lockright, Rob Storr full float rear axle, rear discs, YJ springs, virtual lift, 31" Grizzly Claws, beadlock rims, +50mm LR arches, LED rear lights, LED roof spots, bucket seats, Luke harnesses, internal cage
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: king pin bearings have gone in my 410 axle
Ideal chears guys so I will proberly order 2 new ones ideal as I can start to put it back together Saturday and fit the new ones when.they come as I am planning on doing the other side if this side goes right I will proberly do it on.christmas day lol as I ordered 2 sets of kingpin bearings and seals as the other side has play in it as I put new wheel bearings in 1 mounth ago so soon the front will have new bearings and seals
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: king pin bearings have gone in my 410 axle
All back togheter and all working just got to tighten up my wheel bearings a little bit as I only put new ones in 1 month ago plus the other kingpin bearings on.the drivers side are in good condition still so I will do them in 2-4 months time
Also what is the purphase of this guys as jimnys don't have them.
Also what is the purphase of this guys as jimnys don't have them.
- Attachments
-
- IMAG0384.jpg (1.1 MiB) Viewed 6672 times
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT