1.3 1.6 inlet manifold

Engine not running right? see if we can help you!
Post Reply
User avatar
timwilks13
SCUK Website Padawan
SCUK Website Padawan
Posts: 1248
Joined: Sun Feb 03, 2013 5:55 am
Location: Scarborough, soon to be Poland

1.3 1.6 inlet manifold

Post by timwilks13 » Sat Jan 11, 2014 11:36 am

I have put my 1.3 manifold onto the 1.6 block as it was modded for the su, but noticed the inlet holes are slightly bigger on the 1.6 than the 1.3, will this cause any issues?
1986 SJ410 - Furry dice, new window winder.

10 kinds of people in this world, those who understand binary and those who dont.

if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
Top
trotter
Winching along now
Winching along now
Posts: 617
Joined: Tue Apr 15, 2008 5:59 pm
Location: behind you

Re: 1.3 1.6 inlet manifold

Post by trotter » Sat Jan 11, 2014 11:49 am

Ever so slight power loss but as its a off roaster and not a race car it prob not even noticeable I did same on mine
if in doubt, FLAT OUT!

mans tool kit > duct tape, wd40 and a bfh is all you ever need
Top
User avatar
twiss
SCUK Computer Wizard
SCUK Computer Wizard
Posts: 6110
Joined: Mon Nov 08, 2010 2:28 pm
Location: Birkirkara, Malta
Contact:
Contact twiss

Re: 1.3 1.6 inlet manifold

Post by twiss » Sat Jan 11, 2014 1:15 pm

Yeah it won't make much of a noticeable difference to be honest
Twiss

'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410

"If brute force doesn't fix your problem, you aren't using enough of it."
Top
User avatar
dan_2k_uk
I spend far too much time on here
I spend far too much time on here
Posts: 4924
Joined: Tue May 06, 2008 5:19 pm
Location: Swindon, Wiltshire

Re: 1.3 1.6 inlet manifold

Post by dan_2k_uk » Sat Jan 11, 2014 1:24 pm

It will probably only effect the top end if anything.
Image
Janspeed manifold, LWB Vit vented discs and calipers

Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Top
User avatar
timwilks13
SCUK Website Padawan
SCUK Website Padawan
Posts: 1248
Joined: Sun Feb 03, 2013 5:55 am
Location: Scarborough, soon to be Poland

Re: 1.3 1.6 inlet manifold

Post by timwilks13 » Sat Jan 11, 2014 5:07 pm

Of you lot that have done this what fuel pump did you use? Just looking on eBay and there are hundreds to choose from!!
1986 SJ410 - Furry dice, new window winder.

10 kinds of people in this world, those who understand binary and those who dont.

if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: 1.3 1.6 inlet manifold

Post by Jordi » Sat Jan 11, 2014 6:16 pm

Facet low pressure pump. 1-4psi I think.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
twiss
SCUK Computer Wizard
SCUK Computer Wizard
Posts: 6110
Joined: Mon Nov 08, 2010 2:28 pm
Location: Birkirkara, Malta
Contact:
Contact twiss

Re: 1.3 1.6 inlet manifold

Post by twiss » Sat Jan 11, 2014 9:42 pm

Mines like this... not had any problems with it... ideal psi is about 3.5 iirc

http://www.ebay.co.uk/itm/Facet-12v-Low ... 5d418a293f


Click Here for Ebay Listing
Twiss

'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410

"If brute force doesn't fix your problem, you aren't using enough of it."
Top
Post Reply

Return to “Engine”