Samurai shell resto.

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
Post Reply
dndnk
Got muddy boots
Got muddy boots
Posts: 62
Joined: Fri Feb 25, 2011 8:17 pm
Location: Warwickshire

Re: Samurai shell resto.

Post by dndnk » Fri Jan 24, 2014 7:50 am

you don't mess about , mind have a nice big shed to work in must help , not on a drive way and neighbours to worry about .
SJ 410 currently off road waiting to leap out of hibernation.

Please visit wifes web site http://www.apassionforcakes.co.uk/index.htm you might even find a zuke on there :-)
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Samurai shell resto.

Post by Jordi » Mon Jan 27, 2014 8:50 pm

DSC_0258.JPG
DSC_0258.JPG (2.8 MiB) Viewed 5767 times
DSC_0259.JPG
DSC_0259.JPG (2.51 MiB) Viewed 5767 times
DSC_0261.JPG
DSC_0261.JPG (2.55 MiB) Viewed 5767 times
Stripped a bit further
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Samurai shell resto.

Post by Jordi » Tue Jan 28, 2014 11:44 pm

Made a start on cutting the rear arches out. I've decided to cut them right out and make complete new arches. I'm cutting around the top on the wheel arch groove for extra clearance as my current fronts (cut to the bottom of the groove) only have 10/15mm clearance with 50mm extended bump stops. When I finally fit the YJs I intend to raise the bump stops again for maximum flex.

Photos to follow.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
dan_2k_uk
I spend far too much time on here
I spend far too much time on here
Posts: 4924
Joined: Tue May 06, 2008 5:19 pm
Location: Swindon, Wiltshire

Re: Samurai shell resto.

Post by dan_2k_uk » Tue Jan 28, 2014 11:47 pm

Good stuff :thumbup:
Image
Janspeed manifold, LWB Vit vented discs and calipers

Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Samurai shell resto.

Post by Jordi » Tue Jan 28, 2014 11:52 pm

dan_2k_uk wrote:Good stuff :thumbup:
Im trying, short on cash and time at the moment. Hoping to get another few hours at it this weekend. Aiming to have everything cut out (sills, arches, bulkhead, any rust) then order a job lot of steel in one go to fill all the gaps back in.

I have a cunning idea to prevent the sills filling with mud and water again but im not quite sure it will work yet.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
Edweird
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2531
Joined: Sat Jan 23, 2010 11:04 pm
Location: Brigg, North Lincolnshire

Re: Samurai shell resto.

Post by Edweird » Wed Jan 29, 2014 1:55 am

Jordi wrote:I have a cunning idea to prevent the sills filling with mud and water again but im not quite sure it will work yet.
Is it as cunning as a fox what used to be Professor of Cunning at Oxford University but has moved on and is now working for the U.N. at the High Commission of International Cunning Planning?
There's three ways of doing things:

The right way,
The wrong way
And my way, which is like the wrong way but faster.
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Samurai shell resto.

Post by Jordi » Wed Jan 29, 2014 7:02 am

Edweird wrote:
Jordi wrote:I have a cunning idea to prevent the sills filling with mud and water again but im not quite sure it will work yet.
Is it as cunning as a fox what used to be Professor of Cunning at Oxford University but has moved on and is now working for the U.N. at the High Commission of International Cunning Planning?
Probably not
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
ScottieJ
The Boss
The Boss
Posts: 11621
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Samurai shell resto.

Post by ScottieJ » Wed Jan 29, 2014 9:15 am

This is gonna be a kickass tintop! Can't wait to see it done!!
Zuki Build

Steady as she goes!
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Samurai shell resto.

Post by Jordi » Wed Jan 29, 2014 5:59 pm

More chopping
Attachments
DSC_0264.JPG
DSC_0264.JPG (2.33 MiB) Viewed 5717 times
DSC_0265.JPG
DSC_0265.JPG (2.48 MiB) Viewed 5717 times
DSC_0266.JPG
DSC_0266.JPG (2.2 MiB) Viewed 5717 times
DSC_0268.JPG
DSC_0268.JPG (2.35 MiB) Viewed 5717 times
DSC_0269.JPG
DSC_0269.JPG (2.11 MiB) Viewed 5717 times
DSC_0270.JPG
DSC_0270.JPG (1.94 MiB) Viewed 5717 times
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Samurai shell resto.

Post by Jordi » Wed Jan 29, 2014 6:04 pm

Found this awesome multi layered floor repair panels. I think I may need to replace it, I really did wonder why the grinder was struggling through it.
DSC_0271.JPG
DSC_0271.JPG (2.29 MiB) Viewed 5715 times
The majority of the rear arches are cut to shape, just the niggly bit round the seat belt housing to sort. Few small floor panels will need to be done. I've cut most of the passenger sill out. I'm trying to set it as close to the floor pan as i can so I can fit the new sill in nice and tight to it.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
Post Reply

Return to “Builds and Projects”