I think I'll keep my Calmini kit.
SAS conversion
SAS conversion
I think I'll keep my Calmini kit.
2006 Jimny JLX+ 1.3 VVT
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
-
twiss
- SCUK Computer Wizard
- Posts: 6110
- Joined: Mon Nov 08, 2010 2:28 pm
- Location: Birkirkara, Malta
- Contact:
Re: SAS conversion
That is a bit awful. In not known for the quality of my fabrication but how could you finish that and think it was good???
Twiss
'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410
"If brute force doesn't fix your problem, you aren't using enough of it."
'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410
"If brute force doesn't fix your problem, you aren't using enough of it."
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: SAS conversion
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
-
donkeychomp
- I spend far too much time on here
- Posts: 3582
- Joined: Thu Aug 18, 2011 3:49 pm
- Location: Shepperton, Middx
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: SAS conversion
Bet he was dead proud of it.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: SAS conversion
That shackle bolt doesn't have a nyloc nut fitted
Thats just outright dangerous and irresponsible
Im sickend as this guy is clearly an engineering guru.
Thats just outright dangerous and irresponsible
Im sickend as this guy is clearly an engineering guru.
Andys Rusty Suzuki Emporium
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: SAS conversion
Looks like YJs
The drivers spring is inside out though. Clearly a well thought out setup.
The drivers spring is inside out though. Clearly a well thought out setup.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Re: SAS conversion
That's so much fail, I can't even start talking about it!
It's not a question of how much you spend on your suzuki, but when your money will run out
Re: SAS conversion
I need this dudes number so he can work on my Zukis 