Manual Hubs - Guide

All tech relating to the newest bread of suzuki 4x4s
Post Reply
User avatar
zook123
SCUK Addict
SCUK Addict
Posts: 948
Joined: Sun Apr 20, 2008 10:48 pm
Location: Shepton Mallet

Manual Hubs - Guide

Post by zook123 » Tue Jan 09, 2018 11:02 am

Tools Required
E10 Torx Socket + Driver Set
10MM Allen Key
T15 Torx Allen Key
Paper Towel / Old Rag

There is no need to disconnect the battery, chock the wheels / do the rain dance. The vehicle can stay on the ground with no need of jacking up.

So, I purchased a pair of AVM hubs online, these were highly recommended in the Jimny community, and these are the High Performance pair, so should last a little longer!
Image
AVM457HP

These did not need the adaptor plates as they are designed for the Jimny.

Remove the old Vacuum Hubs using the E10 Torx, unscrew and throw into the bin.
Image

Clean up the mounting face, it doesn't have to be perfect but free of most grit and grime.
Image

Now is the time if you are fitting SJ or Vitara hubs to fit the adaptor plates, just apply a little grease (not excessive)

Take the new Hubs, and remove the small bolts holding the front on and remove, place the paper gasket onto the hub on the vehicle and offer up the hub
Image

Tighten the bolts and ensure the washers are fitted before tightening!
Image

Ignore the instructions, engage the front of the hub to 4x4 and insert into the hub, and do the Torx bolts up
Image

To test, jack the front wheels up and engage both hubs to 4x4, this should spin both front wheels.

REMINDER - Manual Hubs DO NOT NEED GREASE, just clean with paraffin, and lube with diesel.

I do not take any responsibility from issues caused by following this guide.
Image
2002 Jimny O2 Ragtop
Safari Snorkel, Freewheeling Hub Conversion
Diff Breathers, G/Box and T/Box Breathers, 2in Suspension Lift
HD Recovery Points and Winch Plate
Kuhmo KL71 MT / Goodyear Wrangler AT


Wessex 4X4 Reponse - WE411
wessex4x4response.org.uk

SherwoodNash
Winching along now
Winching along now
Posts: 731
Joined: Sat Aug 09, 2014 11:05 am

Re: Manual Hubs - Guide

Post by SherwoodNash » Tue Jan 09, 2018 12:20 pm

Nice guide! should be a stickie somewhere? (can't expand your last pic tho'?)

They look neat, the red really sets them off :thumbup:

User avatar
ScottieJ
The Boss
The Boss
Posts: 11596
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Manual Hubs - Guide

Post by ScottieJ » Tue Jan 09, 2018 12:31 pm

zook123 wrote:
REMINDER - Manual Hubs DO NOT NEED GREASE, just clean with paraffin, and lube with diesel.
It's best to use a light smear of grease with aisin hubs.


You missed a step

Sit back a wait for the plastic internals of the AVM hubs to break :hahaha:

Then swear loudly when the tiny bolts holding the cap on either snap or round off when you try to undo them :hahaha:
Zuki Build

Steady as she goes!

User avatar
zook123
SCUK Addict
SCUK Addict
Posts: 948
Joined: Sun Apr 20, 2008 10:48 pm
Location: Shepton Mallet

Re: Manual Hubs - Guide

Post by zook123 » Tue Jan 09, 2018 12:46 pm

Plastic internals? I couldn't find any??

And agreed on the tiny bolts, I snapped a allen key already on them!

I'll add to this guide how to get the 4WD light to work... if I can.. but I don't know where mine is broken haha!

Thanks Sherwood (What is your name??), they fit perfectly with the red axles haha!
Image
2002 Jimny O2 Ragtop
Safari Snorkel, Freewheeling Hub Conversion
Diff Breathers, G/Box and T/Box Breathers, 2in Suspension Lift
HD Recovery Points and Winch Plate
Kuhmo KL71 MT / Goodyear Wrangler AT


Wessex 4X4 Reponse - WE411
wessex4x4response.org.uk

User avatar
ScottieJ
The Boss
The Boss
Posts: 11596
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Manual Hubs - Guide

Post by ScottieJ » Tue Jan 09, 2018 12:53 pm

zook123 wrote:Plastic internals? I couldn't find any??
They are in the dial/selector section and known for breaking and causing issues.

You should have got some used aisin hubs ;)

Sorry would just never recommend AVM hubs to anyone.
Zuki Build

Steady as she goes!

User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4551
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: Manual Hubs - Guide

Post by ROBBIE » Tue Jan 09, 2018 12:54 pm

If I ever see the Jimny again I will get a pic of the setup I did
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good

SherwoodNash
Winching along now
Winching along now
Posts: 731
Joined: Sat Aug 09, 2014 11:05 am

Re: Manual Hubs - Guide

Post by SherwoodNash » Tue Jan 09, 2018 1:01 pm

zook123 wrote:Thanks Sherwood (What is your name??), they fit perfectly with the red axles haha!
AKA 'Mike' in real life 8-)

Post Reply