LJ80 Recommissioning.

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
User avatar
mk1joe
Winching along now
Winching along now
Posts: 707
Joined: Tue Mar 16, 2010 8:34 pm
Location: gosport

Re: LJ80 Recommissioning.

Post by mk1joe » Tue Apr 07, 2020 5:05 pm

My current time in lockdown has been a constant struggle between being as constructive as possible, and giving into total laziness. Its reminded me I really am quite lazy, but I've been trying to keep the balance.

All of the work I have done has revolved around the front wings, and getting the front end to line up nicely. These new wings are a massive advantage over the old ones, but still needed some fettling. Somehow the spot welds between the outer wings had pulled apart or swollen up and then just been body filleted over. These are supposed to be a nice tight seem, so I ran a cutting disc down them, drilled them and puddle welded them back together.
IMG_20200407_163921.jpg
IMG_20200404_174034.jpg
There was a big chunk missing from the bottom of the grill panel, so it wasn't sitting properly to test fit the wings. I rebuilt it by mirroring the other side which fortunately was still there. The other side is rotten though and still needs to be replaced.
IMG_20200404_175020.jpg
IMG_20200404_175110.jpg
IMG_20200404_175005.jpg
Next up, the N/S Wing overhung the grill by about 5mm. I was quite happy that the grill panel was perfectly symmetrical because I measured it 100 times when I welded it together. I solved this by drilling the spot welds on the inner wing, pulling it over and welding it back together. It looked like somebody had already done this on the other side and it didn't have the same problem.
IMG_20200404_174041.jpg

User avatar
mk1joe
Winching along now
Winching along now
Posts: 707
Joined: Tue Mar 16, 2010 8:34 pm
Location: gosport

Re: LJ80 Recommissioning.

Post by mk1joe » Tue Apr 07, 2020 5:14 pm

The radius on the front corner of the O/S wing was to tight, so didn't marry up properly with the grill panel and didn't match anywhere else. It had some previous rough repairs. So I cut it back quite far to where the edge had a better radius and made a new panel.
IMG_20200326_135541.jpg
IMG_20200326_170302.jpg
IMG_20200404_174817.jpg
With these parts corrected I could make the brackets to hold the wings to the grill. I chose the dimensions based on little rusty bits that where left of the old ones and from a few pictures I'd seen.
IMG_20200404_174800.jpg
IMG_20200404_174729.jpg
IMG_20200404_174740.jpg
IMG_20200404_174809.jpg

User avatar
mk1joe
Winching along now
Winching along now
Posts: 707
Joined: Tue Mar 16, 2010 8:34 pm
Location: gosport

Re: LJ80 Recommissioning.

Post by mk1joe » Tue Apr 07, 2020 5:25 pm

The two upstand brackets that hold the wings to the bulk head had been cut in half and half of each was missing for some reason. I assume they had rotten off at some point. So I made these based on one or two pictures I found. So I think they are close to being right.
IMG_20200406_124426.jpg
IMG_20200404_180239.jpg
IMG_20200406_130609.jpg
This recess where the wing sits in was a million miles too far forward to start with. This obviously wasn't a problem for whoever welded it together previously because they never fitted any proper wings. So I cut it back and boxed it in to match the curve of the new wing. But after doing this I've started to think that I have cut it back too far based on one original bolt hole that is left, and how the other side sits. The back of the wing on the other side sits too far forwards. I have a feeling neither of the wings are the correct shape around this part, and it will need further addressing/reworking.
IMG_20200404_180251.jpg
So that will be the next thing for me to attempt. I might just repeat the same on the other side to match.

Anton
I spend far too much time on here
I spend far too much time on here
Posts: 3859
Joined: Tue Jan 12, 2010 12:12 pm
Location: London

Re: LJ80 Recommissioning.

Post by Anton » Tue Apr 07, 2020 6:10 pm

Brilliant work! Loving it, now that's how I'd like to be spending my time!
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!

My: Build thread To-do list Pay and Play map

User avatar
mk1joe
Winching along now
Winching along now
Posts: 707
Joined: Tue Mar 16, 2010 8:34 pm
Location: gosport

Re: LJ80 Recommissioning.

Post by mk1joe » Fri Sep 25, 2020 9:13 pm

I haven't updated this for aages, but don't fear as I still have the LJ and have still been making progress (very, very slow progress)

I was all geared up to repair and make good of the (incorrect) rear quarters, until I started pulling tons of body filler from them and then lost faith. So I changed tact, bit the bullet and ordered two new panels.
IMG_20200925_202714.jpg
IMG_20200925_202742.jpg
(check out that deep valley of body filler)
IMG_20200830_190132.jpg
IMG_20200830_190154.jpg
These weren't cheap and absolutely broke the bank, so every other panel I need around them I will be making myself.
IMG_20200925_202109.jpg
IMG_20200925_202421.jpg
IMG_20200925_202213.jpg
IMG_20200925_202312.jpg
IMG_20200925_201956.jpg
Once this side is made and tacked in place I will start on the other side and try to coppy closely.

Anton
I spend far too much time on here
I spend far too much time on here
Posts: 3859
Joined: Tue Jan 12, 2010 12:12 pm
Location: London

Re: LJ80 Recommissioning.

Post by Anton » Sat Sep 26, 2020 2:18 pm

Brilliant work!

:popcorn:
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!

My: Build thread To-do list Pay and Play map

User avatar
mk1joe
Winching along now
Winching along now
Posts: 707
Joined: Tue Mar 16, 2010 8:34 pm
Location: gosport

Re: LJ80 Recommissioning.

Post by mk1joe » Tue Sep 29, 2020 8:58 pm

Thanks Anton! I appreciate the apretiation :thumbup:

Eljeeholland want €250 for the little rear corner piece, so tonight's task was to have a bash at making one.
IMG_20200929_191511.jpg
IMG_20200929_191522.jpg
IMG_20200929_201945.jpg

User avatar
donkeychomp
I spend far too much time on here
I spend far too much time on here
Posts: 3583
Joined: Thu Aug 18, 2011 3:49 pm
Location: Shepperton, Middx

Re: LJ80 Recommissioning.

Post by donkeychomp » Tue Sep 29, 2020 9:13 pm

Very nice work indeed!
If it ticks over...leave it

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7525
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: LJ80 Recommissioning.

Post by Jordi » Wed Sep 30, 2020 7:37 am

Looks like some awesome fabrication work going on.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

lundigee
Engaged 4wd low
Engaged 4wd low
Posts: 114
Joined: Sat Oct 19, 2019 11:04 pm

Re: LJ80 Recommissioning.

Post by lundigee » Thu Oct 22, 2020 11:57 pm

What a joy to see, the trouble with flipping through a few posts on a computer you do not get the true feeling of the effort of what you are achieving here. It is just fantastic to see and thank you for sharing it, what a brilliant, highly time consuming job you are doing.

Post Reply