New to the forum

New to SCUK.co.uk? say hello, give us an idea of who you are, and show us a pic of your pride and joy. were friendly and wont bite!
Post Reply
pwcgwynedd
Got muddy boots
Got muddy boots
Posts: 1
Joined: Sat Dec 31, 2011 10:48 pm
Location: Wirral
Contact:

New to the forum

Post by pwcgwynedd » Sat Dec 31, 2011 10:59 pm

Hi....Newbie here.
I'm looking for a anus for getting my jetski to the beach (my peugeot 407 is great at getting stuck in the sand!!), and I'm hearing good things about the SJ's...So I thought I'd sign up here, and find out what I need to know.

Oh....And Happy New Year :doublethumbs:
pwcgwynedd.co.uk Ski North Wales with us

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: New to the forum

Post by turbo-tom » Sat Dec 31, 2011 11:12 pm

welcome to the club :D ,

someone else will be able to shed light on about buying a sj then me :lol: :lol:

, the rearfloor/arches rot quiet bad , normally the chassis are rot free , check bottom of doors etc for rot

try and get one with the 1,6 8v converstion , or 16v even better :brows:

but mechanically wise there pretty good , and there is no ecus to drown in water and kill

go up and down the gears in the gearbox and play around with the transfere box but not at high speeds :lol:

if there is a knob pull it , if there is a switch flick it :lol:
Tom :)

Ford Fiesta ST :D

User avatar
ScottieJ
The Boss
The Boss
Posts: 11635
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: New to the forum

Post by ScottieJ » Sun Jan 01, 2012 12:51 pm

:welcome: to :S:cuk

As tom says the main thing to look out for is rust, look everywhere, under carpets as well if they are still fitted. The hardest area to fix is behind the seats where the floor raises around the body mounts both inside and underneath, if this area is rotton on the underneath then you either need to be able to weld or expect a big repair bill. You need to lift the body off the chassis to repair this area, not that hard but quite time consuming.

Also I'd take a jack and jack up each wheel to check for movement in any wheel or kingpin bearings and to see if the bearings sound rough when the wheel is spun. All bargaining points £30 per wheel bearing to replace and about £50 for a set of kingpin bearings + labour if you can't do it yourself

Check for smoke, knocks or rattles on start up and make sure the engine has not been warmed up before you got there (a sign the owner might be trying to hide something)

Check for oil leaks near the dizzy on the back if the engine, put your fingers around underneath the fuel pump you'll feel a hole, if oil is coming out of there then it needs a new fuel pump about £100 for a genuine one but after market ones are cheaper.
Check around all the diff and transferbox flanges for oil leaks, could be caused by failing bearings. Check propshafts for play in the U-joints and slip yokes.

Most of all take it for a good drive, they don't handle like a sports car but they should drive straight and true with no wobbles, maybe a small amount of bump steer under heavy braking but overall it should handle well and be easy to drive. There should not be any loud whines (a few small ones maybe) or big clunks during gear changes etc.

As with all old cars just give it a good thorough checking over.

Hope that helps
Zuki Build

Steady as she goes!

User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: New to the forum

Post by ROBBIE » Sun Jan 01, 2012 6:07 pm

hello :welcome: to the forum hope you find a good 1 :doublethumbs:
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good

rgonzobull
Engaged 4wd low
Engaged 4wd low
Posts: 185
Joined: Sun Nov 28, 2010 8:16 pm
Location: Manchester

Re: New to the forum

Post by rgonzobull » Tue Jan 03, 2012 8:45 pm

Hi and welcome! My advise if you have never driven one is test drive as many as you can before you buy. Don't be put off by the first you try or see. This will give you an idea of the way they handle and how the various modifications affect them. As well as all the above advise given by others. Good luck in finding a good one you like
LJ80Q

Post Reply