vit 1.6 8v into a JAP 410 wiring

Got an electrical gremlin? Ask the question here.
Post Reply
User avatar
ScottieJ
The Boss
The Boss
Posts: 11596
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

vit 1.6 8v into a JAP 410 wiring

Post by ScottieJ » Fri Feb 26, 2010 12:45 pm

vit 1.6 8v into a JAP 410 wiring

Coil/Dizzy

from loom the Black/White tracer goes to coil +
rev counter if you have one goes to coil-
from dizzy Black/White tracer goes to coil+
from dizzy Brown/White tracer goes to coil-
Brown and Black/Green tracer from loom doesn't need to connect to anything at this end.
7533_309956415467_822975467_9266819_4670884_n.jpg
7533_309956415467_822975467_9266819_4670884_n.jpg (45.38 KiB) Viewed 45741 times
Starter

+feed from battery to + terminal as usual
Black/Yellow tracer from loom to the spade terminal
Black/Green tracer from loom is not needed
7533_309956430467_822975467_9266820_4045101_n.jpg
7533_309956430467_822975467_9266820_4045101_n.jpg (48 KiB) Viewed 45741 times
Alternator

uses the same colour wires as original, (Black/White tracer & White/Red tracer) just wire up to the plug on the alternator
White/Yellow tracer to +terminal
7533_309956450467_822975467_9266821_463451_n.jpg
7533_309956450467_822975467_9266821_463451_n.jpg (40.71 KiB) Viewed 45741 times
Fuel stop solenoid
Usually a green connector on the carb but sometimes brown (There is also a idle up connector but this is not nneded, if the fuel stop connector is green this will be brown and vice versa)

Find a ignition live (black w/white tracer) and connect it to the black w/white tracer wire from the stop solenoid.
Then just earth the back wire.
Zuki Build

Steady as she goes!

jfatboy
Got muddy boots
Got muddy boots
Posts: 51
Joined: Sun Oct 23, 2011 10:11 pm

Re: vit 1.6 8v into a JAP 410 wiring

Post by jfatboy » Wed Oct 26, 2011 5:38 pm

how long does it take to do one of these conversions?
Image

User avatar
twiss
SCUK Computer Wizard
SCUK Computer Wizard
Posts: 6110
Joined: Mon Nov 08, 2010 2:28 pm
Location: Birkirkara, Malta
Contact:

Re: vit 1.6 8v into a JAP 410 wiring

Post by twiss » Wed Oct 26, 2011 6:41 pm

I think the main long part of it is fabricating new mounts for the engine and gearbox...
It's much easier doing it to the 1.3 SJ/Samurai
Twiss

'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410

"If brute force doesn't fix your problem, you aren't using enough of it."

User avatar
ScottieJ
The Boss
The Boss
Posts: 11596
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: vit 1.6 8v into a JAP 410 wiring

Post by ScottieJ » Thu Oct 27, 2011 12:19 pm

If you get all the bits needed I think you could do the conversion in a day, it's not really that hard.
Zuki Build

Steady as she goes!

mr.lers
Got muddy boots
Got muddy boots
Posts: 8
Joined: Mon Feb 04, 2013 6:45 pm

Re: vit 1.6 8v into a JAP 410 wiring

Post by mr.lers » Tue May 07, 2013 12:30 pm

Well finally got round to my conversion 1.6 8v into a 410 tin top it did take me all bank holiday fag and beer breaks included but hey its worth it the boneshaker now flys;) but I've no idle I haven't conected the fuel stop solonoid yet or a brown connecter on the inlet manifold?? What is it? Do I need it? It's a bit of handfull trying to keep it running in traffic...
drive it like you stole it...

User avatar
ScottieJ
The Boss
The Boss
Posts: 11596
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: vit 1.6 8v into a JAP 410 wiring

Post by ScottieJ » Tue May 07, 2013 12:57 pm

mr.lers wrote:Well finally got round to my conversion 1.6 8v into a 410 tin top it did take me all bank holiday fag and beer breaks included but hey its worth it the boneshaker now flys;) but I've no idle I haven't conected the fuel stop solonoid yet or a brown connecter on the inlet manifold?? What is it? Do I need it? It's a bit of handfull trying to keep it running in traffic...
The fuel stop solenoid not being wired up is what is causing it to stall at idle, find a black w/white tracer to wire up the stop solenoid and just earth the black. (now added to the first post)

The other (brown) connector is part of the idle up system and not needed.
Zuki Build

Steady as she goes!

mr.lers
Got muddy boots
Got muddy boots
Posts: 8
Joined: Mon Feb 04, 2013 6:45 pm

Re: vit 1.6 8v into a JAP 410 wiring

Post by mr.lers » Tue May 07, 2013 1:03 pm

Nice one Scottie that is me sorted and so promptly :)
drive it like you stole it...

The Bird Man
Engaged 4wd low
Engaged 4wd low
Posts: 203
Joined: Fri Mar 15, 2013 2:51 pm
Location: Boston, Lincolnshire

Re: vit 1.6 8v into a JAP 410 wiring

Post by The Bird Man » Sun Nov 16, 2014 9:18 am

Can anyone tell me what connector block/colour wires go to the ignition barrel please. At the moment I am turning it over by bypassing, using a bit of wire on the starter terminals which I don't really want to keep doing. Many thanks, Eddie :D

User avatar
dazerede
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2141
Joined: Fri Sep 30, 2011 10:23 pm
Location: cornwall callington

Re: vit 1.6 8v into a JAP 410 wiring

Post by dazerede » Sun Jun 26, 2016 3:08 pm

Currently doing mine atm will I need to change the dizzy to a 1.3 as this is mine and do I use a 1.6 coil or 1.3 thanks
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit :)
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT

User avatar
dazerede
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2141
Joined: Fri Sep 30, 2011 10:23 pm
Location: cornwall callington

Re: vit 1.6 8v into a JAP 410 wiring

Post by dazerede » Sun Jun 26, 2016 3:12 pm

I have connected the 1.6 coil up but where do I connect the earth wire as it was connected to the + on the 1.0 coil thanks
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit :)
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT

Post Reply