trotters sammy... updated finally

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
Post Reply
User avatar
ScottieJ
The Boss
The Boss
Posts: 11620
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: trotters sammy... the never ending project...

Post by ScottieJ » Tue Jan 08, 2013 10:31 pm

Well lets see what happens with this 410 but I should have space free for an sj over the next few months so anytime really!

how wide are your alloys? I presume your tyres are 10.5" wide? If so I wouldn't run wheels that are wider than 8" otherwise you'll always be getting crap in the bead!
Zuki Build

Steady as she goes!

trotter
Winching along now
Winching along now
Posts: 617
Joined: Tue Apr 15, 2008 5:59 pm
Location: behind you

Re: trotters sammy... the never ending project...

Post by trotter » Thu Jun 27, 2013 11:03 pm

just fixed all the broken picture links... seems to take forever! (note to self don't move offroading and suzuki picture folders around in photobucket EVER again!!)
if in doubt, FLAT OUT!

mans tool kit > duct tape, wd40 and a bfh is all you ever need

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: trotters sammy... the never ending project...

Post by turbo-tom » Thu Jun 27, 2013 11:20 pm

I learnt that mistake with bookface!
Tom :)

Ford Fiesta ST :D

trotter
Winching along now
Winching along now
Posts: 617
Joined: Tue Apr 15, 2008 5:59 pm
Location: behind you

Re: trotters sammy... the never ending project...

Post by trotter » Sat Oct 19, 2013 5:33 pm

well its been quite a while since i've bothered to get the spanners out. Only managed a few bits for about hour and a half today before it poured with rain but its a start at least

I got the vitara water rail fitted, as i couldnt use the sj one because the bolt holding it on snapped off in the engine block. Also had to do a bit of a cut and shut on the pipework from the bulkhead - water rail, as i didnt have a pipe long enough so i cut 2 down and made a copper insert at work to fit inside the joining pipes, hopefully with 2 jubilee clips it should hold fine.

Image

Image

the never ending list of things left to do are:

Fit
new alternator
jimny ps box
vit ps pump and res + pipes

Then fingers crossed the engine works ok. Then it will be off for mot

At some point, hopefully in the near future it will benefit from a virtual lift, box section sills (possibly haven't decided yet), YJ springs, Low Range Offroad YJ conversion kit, wheels and tyres fitted, winch bumper fitted, winch fitted, bucket seats fitted, possible rocklobster ( will see how 410 t box copes )

still it will be finished one day :D
if in doubt, FLAT OUT!

mans tool kit > duct tape, wd40 and a bfh is all you ever need

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: trotters sammy... the never ending project...

Post by Jordi » Sat Oct 19, 2013 10:39 pm

Glad you managed get a bit of time for it bud. Nice list of expensive jobs to get on with.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

trotter
Winching along now
Winching along now
Posts: 617
Joined: Tue Apr 15, 2008 5:59 pm
Location: behind you

Re: trotters sammy... the never ending project...

Post by trotter » Sun Oct 20, 2013 5:11 pm

Yea its been sat there getting lonely for too long, fingers crossed it will be sorted soon then next time I will be able to come laning with everyone
if in doubt, FLAT OUT!

mans tool kit > duct tape, wd40 and a bfh is all you ever need

trotter
Winching along now
Winching along now
Posts: 617
Joined: Tue Apr 15, 2008 5:59 pm
Location: behind you

Re: trotters sammy... the never ending project...

Post by trotter » Tue Oct 29, 2013 7:27 pm

quick update

the engine turned over and even ran for a little bit earlier so with a bit of fine tuning this weekend hopefully i can be otr mid nov
if in doubt, FLAT OUT!

mans tool kit > duct tape, wd40 and a bfh is all you ever need

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: trotters sammy... the never ending project...

Post by Jordi » Tue Oct 29, 2013 7:54 pm

:doublethumbs:
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
twiss
SCUK Computer Wizard
SCUK Computer Wizard
Posts: 6110
Joined: Mon Nov 08, 2010 2:28 pm
Location: Birkirkara, Malta
Contact:

Re: trotters sammy... the never ending project...

Post by twiss » Wed Oct 30, 2013 9:09 am

Wooo good to hear you're aiming for mid nov!!! Sorry again about stealing your alternator ;)
Twiss

'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410

"If brute force doesn't fix your problem, you aren't using enough of it."

trotter
Winching along now
Winching along now
Posts: 617
Joined: Tue Apr 15, 2008 5:59 pm
Location: behind you

Re: trotters sammy... the never ending project...

Post by trotter » Wed Oct 30, 2013 9:53 pm

Ha no worries twiss, it made me pull my finger out and get a bigger one so it will work with my winch
if in doubt, FLAT OUT!

mans tool kit > duct tape, wd40 and a bfh is all you ever need

Post Reply