new from norht yorkshire
- Darrell
- Suzuki, will you marry me?
- Posts: 2988
- Joined: Wed Feb 23, 2011 7:54 pm
- Location: south oxfordshire
- Contact:
Re: new from norht yorkshire
Welcome to the club
avatar if you want it..
avatar if you want it..
- Attachments
-
- DSC_0028.jpg (15.96 KiB) Viewed 6337 times
2005-GV 1600se, "Hell" What do I know!
Re: new from norht yorkshire
cheers guys,
im from whitby.
yeh its still got leafs on the front over axle but unknown dampers.
thanks for the avatar pic
just want to get it running a bit better and have a bit more power. also need to sort some sort of snorkel and buy a winch.
im from whitby.
yeh its still got leafs on the front over axle but unknown dampers.
thanks for the avatar pic
just want to get it running a bit better and have a bit more power. also need to sort some sort of snorkel and buy a winch.
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: new from norht yorkshire
Not too far away from me.
Can't say i know much about 35s. I'm planning on going to 33s soon as i've fitted my 1600 and rocklobster.
Jordi
Can't say i know much about 35s. I'm planning on going to 33s soon as i've fitted my 1600 and rocklobster.
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: new from norht yorkshire
where abouts do you go play??
think i might drop down to 33's if i can find some. just read that anything over 33's and your asking for trouble with breakages.
think i might drop down to 33's if i can find some. just read that anything over 33's and your asking for trouble with breakages.
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: new from norht yorkshire
33s is the limit for a standard setup then you need to look into hardened shafts and anti wrap etc.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: new from norht yorkshire
Haven't done a lot the last year.
Joined north east laners and went out up near hexham a few weeks ago. They have a weekend planned at Scarborough too. Might have been this weekend.
Theres a site near stanley called Pea Farm. I'm going to try and get to Tong too.
Plus there is the SCUK 2013 meet in planning.
Jordi
Joined north east laners and went out up near hexham a few weeks ago. They have a weekend planned at Scarborough too. Might have been this weekend.
Theres a site near stanley called Pea Farm. I'm going to try and get to Tong too.
Plus there is the SCUK 2013 meet in planning.
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: new from norht yorkshire
hmm, hardened shafts. i take it they tend to snap under the strain?? i am being thick but what is anti wrap??
ok cool, just looked on ne-laners, it was yesterday, bugger, they will have drove past my house to scarborough. ive done tong before, used to go quite often a few year back. great place. there is also wilton in redcar which is supposed to be a good spot.
ok cool, just looked on ne-laners, it was yesterday, bugger, they will have drove past my house to scarborough. ive done tong before, used to go quite often a few year back. great place. there is also wilton in redcar which is supposed to be a good spot.
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: new from norht yorkshire
Shafts and CVs are weak spots. Axle wrap is the axle twisting (nose of diff lifting up) with the increased torque required to get bigger tyres turning.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: new from norht yorkshire
35 incy tyres well that is big mike harris has a set of 33/12.50/r15 boggers
and he has hardened shafts and also strengthened the axles
we would love more pics of ur zook
and he has hardened shafts and also strengthened the axles
we would love more pics of ur zook
- Attachments
-
- mike harris zook.jpg (300 KiB) Viewed 6269 times
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: new from norht yorkshire
Wilton has apparently closed. Rogerley quarry closed. Weardale Off Road is now a £50 an hour corporate kinda place. That Langdale Quest closed???
Think there is still a PnP at Robin Hoods bay?
Jordi
Think there is still a PnP at Robin Hoods bay?
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank