- image.jpg (2.52 MiB) Viewed 4222 times
- image.jpg (2.71 MiB) Viewed 4222 times
Jordis 1988 Samurai (Re)Build
-
Jordi
- Bow down before me
- Posts: 7534
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Jordi's 1988 Samurai Build
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: Jordi's 1988 Samurai Build
Looking good
1994 sj 413 sierra
cheker plate door cards
cd players
asin free wheeling hubs
99% rust free
alloys
bukets
some leaks here and there
cheker plate door cards
cd players
asin free wheeling hubs
99% rust free
alloys
bukets
some leaks here and there
Re: Jordi's 1988 Samurai Build
Nuthing wrong with a patchwork car
1994 sj 413 sierra
cheker plate door cards
cd players
asin free wheeling hubs
99% rust free
alloys
bukets
some leaks here and there
cheker plate door cards
cd players
asin free wheeling hubs
99% rust free
alloys
bukets
some leaks here and there
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: Jordi's 1988 Samurai Build
Skittles mo-fo!
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
Re: Jordi's 1988 Samurai Build
Wwwwiiiiiiiiddddddddddeeeeee think I would loose the wheels spacers, I think your wheel bearings will want you as well 
-
Jordi
- Bow down before me
- Posts: 7534
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Jordi's 1988 Samurai Build
Just whipped the spacers of now Scottie.
As said needs the sills trimming a bit for some clearance. On the flat lock to lock its not fouling on the chassis or springs though.
It may now be the time to move the front axle forward and shim it.
As said needs the sills trimming a bit for some clearance. On the flat lock to lock its not fouling on the chassis or springs though.
It may now be the time to move the front axle forward and shim it.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Jordi's 1988 Samurai Build
Ace. I need to get this shed built so I can get back on with the zook.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
Jordi
- Bow down before me
- Posts: 7534
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Jordi's 1988 Samurai Build
Cheers for the kind words chaps. Its getting there.
I just need to get my fingure out and do some body work. The plan is to cut out the sills again, looking as it i dont think it effects the actual body, just the box section. That SHOULD be a quick job. Cut the ends and box in again.
New front clip, bit of a time consuming one as it needs virtual lifting and patching to fit.
Wheels to finish wite brushing, prime, and spray satin black.
I could do with a few spare days, last time it was all properly bodged together. I'd like to take a bit more time when i redo it. I'm hoping i'll do a better job of it as i think i'm a bit more experienced this time round. We'll see.
Till i get that done i'll just do more temporary bodges.
Edit :- i'm back at work again now warminster bound. Another weekend gone.
I just need to get my fingure out and do some body work. The plan is to cut out the sills again, looking as it i dont think it effects the actual body, just the box section. That SHOULD be a quick job. Cut the ends and box in again.
New front clip, bit of a time consuming one as it needs virtual lifting and patching to fit.
Wheels to finish wite brushing, prime, and spray satin black.
I could do with a few spare days, last time it was all properly bodged together. I'd like to take a bit more time when i redo it. I'm hoping i'll do a better job of it as i think i'm a bit more experienced this time round. We'll see.
Till i get that done i'll just do more temporary bodges.
Edit :- i'm back at work again now warminster bound. Another weekend gone.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank