Mikes lwb build and repairs !
-
ROBBIE
- I spend far too much time on here
- Posts: 4555
- Joined: Tue Sep 09, 2008 6:32 pm
- Location: Dorset or stuck
Re: Mikes rotten Kja PROGRESS !!! :)
Why you cutting the cab? And what way side to side or front to back?
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Jimny 1.6 not as good as an SJ but still good
-
timwilks13
- SCUK Website Padawan
- Posts: 1248
- Joined: Sun Feb 03, 2013 5:55 am
- Location: Scarborough, soon to be Poland
Re: Mikes rotten Kja PROGRESS !!! :)
Or top to bottom?!ROBBIE wrote:Why you cutting the cab? And what way side to side or front to back?
Seriously though why do you need to cut the cab in half? If its for repair purposes it seems like a backwards step, but if its to see how many cutting disks it takes to cut a cab in half, then its the perfect way to find out.
1986 SJ410 - Furry dice, new window winder.
10 kinds of people in this world, those who understand binary and those who dont.
if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
10 kinds of people in this world, those who understand binary and those who dont.
if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Mikes rotten Kja PROGRESS !!! :)
If its just floor and roof through the door area I reckon it will only take 4 if they are the really narrow good ones.timwilks13 wrote:Or top to bottom?!ROBBIE wrote:Why you cutting the cab? And what way side to side or front to back?
Seriously though why do you need to cut the cab in half? If its for repair purposes it seems like a backwards step, but if its to see how many cutting disks it takes to cut a cab in half, then its the perfect way to find out.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Re: Mikes rotten Kja PROGRESS !!! :)
im going to guess its a case of removing the kja specific bit of the cab
(rear panel and roof down to scuttle top and grafting it onto the front/lower
floor pan of the white soft top. kjas have a return on the back panel
to cover where the standard floor pan bends up to meet the rear floor of
a normal sj. this bit is usually rotten or plated to buggery so cuting it off
is probably easiest. id drill the spot welds out from the scuttle area seem and
sawp the lot over then plug weld it back up.
(rear panel and roof down to scuttle top and grafting it onto the front/lower
floor pan of the white soft top. kjas have a return on the back panel
to cover where the standard floor pan bends up to meet the rear floor of
a normal sj. this bit is usually rotten or plated to buggery so cuting it off
is probably easiest. id drill the spot welds out from the scuttle area seem and
sawp the lot over then plug weld it back up.
Andys Rusty Suzuki Emporium
Re: Mikes rotten Kja PROGRESS !!! :)
I'm sure a spot weld drill bit would do a better job of separating the panels although it would take longer. I do remember that Tim Pink cut his in half to extend the cab.
2006 Jimny JLX+ 1.3 VVT
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
-
mike harris
- SCUK is my life
- Posts: 1828
- Joined: Sat Jan 08, 2011 8:30 pm
- Location: hascombe Surrey
Re: Mikes rotten Kja PROGRESS !!! :)
I'm cutting through the bottom of the pillars, along the bulkhead, over the tunnel
About 3 inches above the sills. Replacing the whole floors, tunnel and the bottom foot of the bulkhead.
Mike
About 3 inches above the sills. Replacing the whole floors, tunnel and the bottom foot of the bulkhead.
Mike
-
mike harris
- SCUK is my life
- Posts: 1828
- Joined: Sat Jan 08, 2011 8:30 pm
- Location: hascombe Surrey
Re: Mikes rotten Kja PROGRESS !!! :)
Backwards step? I think repairing it all in one go is a massive leep forward personally !
All will become clear, I've got a mint samurai body why not use it?!
All will become clear, I've got a mint samurai body why not use it?!
-
timwilks13
- SCUK Website Padawan
- Posts: 1248
- Joined: Sun Feb 03, 2013 5:55 am
- Location: Scarborough, soon to be Poland
Re: Mikes rotten Kja PROGRESS !!! :)
More than 4 discs then I recon dan.mike harris wrote:I'm cutting through the bottom of the pillars, along the bulkhead, over the tunnel
About 3 inches above the sills. Replacing the whole floors, tunnel and the bottom foot of the bulkhead.
Mike
1986 SJ410 - Furry dice, new window winder.
10 kinds of people in this world, those who understand binary and those who dont.
if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
10 kinds of people in this world, those who understand binary and those who dont.
if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
-
mike harris
- SCUK is my life
- Posts: 1828
- Joined: Sat Jan 08, 2011 8:30 pm
- Location: hascombe Surrey
Re: Mikes rotten Kja PROGRESS !!! :)
Il use a recip saw, cut through both sides of the pillar at once
Re: Mikes rotten Kja PROGRESS !!! :)
I think it was the wording that confused people....."chopping in half" sounds like you are either cutting it down the middle lengthways or sideways 