1987 sj410 xud engine, coil sprung and Toyota axles
- d_r_1989
- Winching along now
- Posts: 524
- Joined: Tue Jul 08, 2014 1:49 pm
- Location: Halifax west Yorkshire
1987 sj410 xud engine, coil sprung and Toyota axles
So after getting 99% done with my blue sj I'm now ready to make my off-road SJ roadworthy and hopefully I might actually use it instead of the blue one.
It might not be to everyone's taste but it has sentimental value to me and I'm trying to keep to its roots but improve its off-road ability and loose the rot which it has plenty of.
I'm using another shell, well bottom half and then extending to roughly 90" wheelbase and making a back that is very similar to sj shape, half cage and 70series Toyota axles
It might not be to everyone's taste but it has sentimental value to me and I'm trying to keep to its roots but improve its off-road ability and loose the rot which it has plenty of.
I'm using another shell, well bottom half and then extending to roughly 90" wheelbase and making a back that is very similar to sj shape, half cage and 70series Toyota axles
Last edited by d_r_1989 on Wed Sep 28, 2022 11:35 am, edited 1 time in total.
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: 1987 sj410 xud engine and coil springs
Other than being a dirty diesel i’m looking forward to seeing the build.
Based on the fabrication work on the other SJ i expect this to be just as impressive.
Based on the fabrication work on the other SJ i expect this to be just as impressive.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
- d_r_1989
- Winching along now
- Posts: 524
- Joined: Tue Jul 08, 2014 1:49 pm
- Location: Halifax west Yorkshire
Re: 1987 sj410 xud engine and coil springs
Your right on the dirty diesel, and to anyone who thinks diesel is better it isn't. It's just heavier. Though it does have a lovely bit of turbo chatter on hill climbs.
But thank you for the kind words, this one will go the same but abit less of a show queen finish so I'm not scared to scratch it.
But thank you for the kind words, this one will go the same but abit less of a show queen finish so I'm not scared to scratch it.
- ROBBIE
- I spend far too much time on here
- Posts: 4555
- Joined: Tue Sep 09, 2008 6:32 pm
- Location: Dorset or stuck
Re: 1987 sj410 xud engine and coil springs
Might be dirty diesel, but 1.9xud is a wonderful bit of kit
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Jimny 1.6 not as good as an SJ but still good
- d_r_1989
- Winching along now
- Posts: 524
- Joined: Tue Jul 08, 2014 1:49 pm
- Location: Halifax west Yorkshire
Re: 1987 sj410 xud engine and coil springs
Xud is a good engine. Just a weighty one. Can't say it's hindered the off-road performance at all though, just changed the characteristic of an SJ. Not fire in and rev to the moon anymore
Progress is slow at the moment with a house move and unit move but pictures will be coming soon
Progress is slow at the moment with a house move and unit move but pictures will be coming soon
- d_r_1989
- Winching along now
- Posts: 524
- Joined: Tue Jul 08, 2014 1:49 pm
- Location: Halifax west Yorkshire
Re: 1987 sj410 xud engine and coil springs
Well overdue update. So iv finally moved house and out of my unit. The SJ is at a friend's unit and he's helping me get it done, he has alot of experience in off-road car building so progress should start speeding up soon.
At the moment iv stripped the back Toyota axle ready, redesigned the inlet manifold for more bulkhead clearance and pretty much been ordering bits.
It's looking in a sorry state but this will change, it's not going to be as pretty as my blue one as it is primarily for off-road/heavy green lane use but it will still have the same care and attention underneath.
At the moment iv stripped the back Toyota axle ready, redesigned the inlet manifold for more bulkhead clearance and pretty much been ordering bits.
It's looking in a sorry state but this will change, it's not going to be as pretty as my blue one as it is primarily for off-road/heavy green lane use but it will still have the same care and attention underneath.
- donkeychomp
- I spend far too much time on here
- Posts: 3582
- Joined: Thu Aug 18, 2011 3:49 pm
- Location: Shepperton, Middx
Re: 1987 sj410 xud engine, coil sprung and Toyota axles
A lot of work for sure but I bet it'll be great fun!
If it ticks over...leave it
Re: 1987 sj410 xud engine, coil sprung and Toyota axles
Looking forward to the progress! Sure it's gonna be unstoppable
SJ413 LWB Santana 33s, 94",
- d_r_1989
- Winching along now
- Posts: 524
- Joined: Tue Jul 08, 2014 1:49 pm
- Location: Halifax west Yorkshire
Re: 1987 sj410 xud engine, coil sprung and Toyota axles
Steady progress but things are coming together. You can see the lines where the axles were originally and how far they have moved.
Also got a really good deal on some new wheels and 33" tyre combo
Also got a really good deal on some new wheels and 33" tyre combo
- d_r_1989
- Winching along now
- Posts: 524
- Joined: Tue Jul 08, 2014 1:49 pm
- Location: Halifax west Yorkshire
Re: 1987 sj410 xud engine, coil sprung and Toyota axles
So iv not been down as much as I'd like but my friend Mr sunderland has been making abit of progress. His work is always top notch