hi all!
-
mysjisbrokenagain
- Got muddy boots
- Posts: 7
- Joined: Fri Jul 11, 2008 10:57 am
- Location: swindon
hi all!
hi my names gavin, im 24 from swindon and finally got off my ass and brought an e reg sj 410 vx resprayed matt black on the outside with a 2inch lift a month ago! All was well until last week when complete engine failure occured! I think i've narrowed it down to a faulty carb but after 4days of tinkering still no joy! I will post pic's when its running and out of my garage! Hi to existing members dan and trotter!
Re: hi all!
Welcome to the forum matey!
I'm from just down the road in Chippenham, been out with Trotter a few times but haven't yet been for blast with Dan since he's got his Sammy finished!
we'll have to all go out laning once you've got it sorted! Have you stripped the carb and given the jets a clean, could just be blocked with crap!
I'm from just down the road in Chippenham, been out with Trotter a few times but haven't yet been for blast with Dan since he's got his Sammy finished!
we'll have to all go out laning once you've got it sorted! Have you stripped the carb and given the jets a clean, could just be blocked with crap!
Re: hi all!
howdy glad u finally made it 
if in doubt, FLAT OUT!
mans tool kit > duct tape, wd40 and a bfh is all you ever need
mans tool kit > duct tape, wd40 and a bfh is all you ever need
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: hi all!
good work 
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Re: hi all!
Hello Gavin, welcome to the froum!
Dan
Dan
http://www.suzukiclubuk.co.uk the new home for your suzuki sj
-
urbanzook
- Winching along now
- Posts: 526
- Joined: Tue Jul 08, 2008 8:04 pm
- Location: stevenage
- Contact:
Re: hi all!
Hello Gavin, welcome to the froum hope all gose well with the tinkering
-
mysjisbrokenagain
- Got muddy boots
- Posts: 7
- Joined: Fri Jul 11, 2008 10:57 am
- Location: swindon
Re: hi all!
after all my dad's and mine hard work and basically half an engine re-build its alive again and breathing! Well breathing blue smoke anyway! But im 99% sure its the valve stem seals gone! Good enough for now tho!
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: hi all!
good news! I went 2 calne the bumpy way after work. A lot of water on yatesbury lane. Went thru 2 fast and the f#@KER decided to die. Need a new rubber seal 4 my distributor cap!
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
urbanzook
- Winching along now
- Posts: 526
- Joined: Tue Jul 08, 2008 8:04 pm
- Location: stevenage
- Contact:
Re: hi all!
use a washing up glove, cut the end off the fingers off,, cabel ty them on the leeds, 5 leeds five fingers, an a big one round the bottom, jd one walter prof dizy
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: hi all!
have heard of others doing this so will have to give it a go
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.