well here i am

New to SCUK.co.uk? say hello, give us an idea of who you are, and show us a pic of your pride and joy. were friendly and wont bite!
Post Reply
User avatar
dan_2k_uk
I spend far too much time on here
I spend far too much time on here
Posts: 4924
Joined: Tue May 06, 2008 5:19 pm
Location: Swindon, Wiltshire

Re: well here i am

Post by dan_2k_uk » Wed Oct 16, 2013 11:49 pm

Welcome. Virtual lift all the way :D
Image
Janspeed manifold, LWB Vit vented discs and calipers

Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Top
User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: well here i am

Post by ROBBIE » Thu Oct 17, 2013 8:54 am

Howdy :welcome:
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Top
User avatar
kiwizook
SCUK Addict
SCUK Addict
Posts: 878
Joined: Fri Dec 28, 2012 2:36 am
Location: Masterton, NZ

Re: well here i am

Post by kiwizook » Thu Oct 17, 2013 9:24 am

ScottieJ wrote: I'll give him a chance wolly if he's a :tosser: I'll get rid of him :mrgreen:

:hahaha: :hahaha: :hahaha:
It's not a question of how much you spend on your suzuki, but when your money will run out
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: well here i am

Post by Jordi » Thu Oct 17, 2013 9:31 am

minibreaker wrote:i think looking at it that the spring over will be enough for the look i am after and i think with 33s with spacers i should be ok for stability. i may just end up with 31s and a 2 inch body lift but who knows
33s on spacers? Hope you have a good supply of bearings. They stick out so far the strain on the bearings and hubs causes things to wear out very quickly.
image.jpg
image.jpg (1.07 MiB) Viewed 3740 times
SPOA will give enough lift for 33s you may find that the tyres still foul on the bulkhead on lock and articulation.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
waynesworld
Got muddy boots
Got muddy boots
Posts: 56
Joined: Wed Oct 16, 2013 4:07 pm

Re: well here i am

Post by waynesworld » Thu Oct 17, 2013 9:57 am

Ye kida a bit much spacers with 33`s, but as said when we spoke, go as wide as you do high and it will be fine, so a 2inch body and spoa with 33/12.50 rubber and you wont be far off.
Top
User avatar
suzukisteve
Suzuki Guru
Suzuki Guru
Posts: 1344
Joined: Sat Feb 04, 2012 10:07 am
Location: Christchurch, Dorset

Re: well here i am

Post by suzukisteve » Thu Oct 17, 2013 10:22 am

:welcome: to the club!
pickle power!
Top
Anton
I spend far too much time on here
I spend far too much time on here
Posts: 3859
Joined: Tue Jan 12, 2010 12:12 pm
Location: London

Re: well here i am

Post by Anton » Thu Oct 17, 2013 2:37 pm

Welcome!

And post pics!

:-)
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!

My: Build thread ● To-do list ● Pay and Play map
Top
Post Reply

Return to “New members”