steering Z bar
Re: steering Z bar
Sounds a bit of a bodge really tbh. Something as critical as steering. I would spend the £200 on a proper kit but if there's a perfectly good cheap alternative then I would do that instead.
Re: steering Z bar
Doesn't matter. Spoke to rob storr today and ordered one. ![:) :)](./images/smilies/icon_e_smile.gif)
![:) :)](./images/smilies/icon_e_smile.gif)
Re: steering Z bar
Just answered the phone as normal. Don't know what your on about haha.
- donkeychomp
- I spend far too much time on here
- Posts: 3583
- Joined: Thu Aug 18, 2011 3:49 pm
- Location: Shepperton, Middx
Re: steering Z bar
Aha so RS Engineering is Rob. I'm going to call him too, think I need one of these on the LJ, hit a pebble and it's all over the place.
If it ticks over...leave it
Re: steering Z bar
Christoff, did you get locking nuts for the track rod ends in your robb storr kit? I've got mine but no locking nuts for the track rods, so nothing to stop them moving/adjusting themselves.
- donkeychomp
- I spend far too much time on here
- Posts: 3583
- Joined: Thu Aug 18, 2011 3:49 pm
- Location: Shepperton, Middx
Re: steering Z bar
Well I called him and he answered!
Kit arrived but no instructions and I'm shaking my head at how to fit this. Going to call him back!
Kit arrived but no instructions and I'm shaking my head at how to fit this. Going to call him back!
If it ticks over...leave it
- Ladaman
- Suzuki Guru
- Posts: 1090
- Joined: Thu Sep 08, 2011 10:56 pm
- Location: Huddersfield, W. Yorkshire
- Contact:
Re: steering Z bar
Your lucky.
I just got my full float kit, eventually, and the shafts are just bits of tube with a thread tapped in each end.
They haven't been machined to my mind.
I did get the machined adaptors though.
![:S :S](./images/smilies/Confused.gif)
I just got my full float kit, eventually, and the shafts are just bits of tube with a thread tapped in each end.
They haven't been machined to my mind.
I did get the machined adaptors though.
![:S :S](./images/smilies/Confused.gif)
YouTube
Ignis Sport 1.5 16V; Jimny gearbox, 410 transfer box; 5.125:1 Vitara diffs; rear Lockright, Rob Storr full float rear axle, rear discs, YJ springs, virtual lift, 31" Grizzly Claws, beadlock rims, +50mm LR arches, LED rear lights, LED roof spots, bucket seats, Luke harnesses, internal cage
Ignis Sport 1.5 16V; Jimny gearbox, 410 transfer box; 5.125:1 Vitara diffs; rear Lockright, Rob Storr full float rear axle, rear discs, YJ springs, virtual lift, 31" Grizzly Claws, beadlock rims, +50mm LR arches, LED rear lights, LED roof spots, bucket seats, Luke harnesses, internal cage
Re: steering Z bar
Eh??? You sure he hasn't sent you steering arms? Get a pic up??Ladaman wrote:Your lucky.
I just got my full float kit, eventually, and the shafts are just bits of tube with a thread tapped in each end.
They haven't been machined to my mind.
I did get the machined adaptors though.
-
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: steering Z bar
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map