rotten sills

fitting new seats? welding up arches? Painting your SJ? post your queries here
Post Reply
kevin9044
Got muddy boots
Got muddy boots
Posts: 33
Joined: Thu Sep 11, 2014 1:05 pm

rotten sills

Post by kevin9044 » Wed Sep 24, 2014 4:59 pm

I have now discovered my sills are totally rotten. Is it easiest to cut out the rot and replace with box section and if so what size? thanks.
Top
User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: rotten sills

Post by ROBBIE » Wed Sep 24, 2014 5:05 pm

I used 100x100 mm box, but not the easiest to weld thick box to bodywork
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Top
User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: rotten sills

Post by ROBBIE » Wed Sep 24, 2014 5:10 pm

Get the tyres size you want then do sills as once it's on it's a pig to cut
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Top
kevin9044
Got muddy boots
Got muddy boots
Posts: 33
Joined: Thu Sep 11, 2014 1:05 pm

Re: rotten sills

Post by kevin9044 » Wed Sep 24, 2014 8:12 pm

Thanks Robbie. I didnt even think about tyre size! Im very new to all this..its my 1st build/renovation.
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: rotten sills

Post by Jordi » Wed Sep 24, 2014 8:53 pm

Made a set.

http://forum.suzukiclubuk.co.uk/vi ... 7&start=70
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
kevin9044
Got muddy boots
Got muddy boots
Posts: 33
Joined: Thu Sep 11, 2014 1:05 pm

Re: rotten sills

Post by kevin9044 » Thu Sep 25, 2014 12:46 am

Looking good Jordi....shame you dont live nearer! :-)
Hope i can get it something like that...think i need some patience and practise.
Top
User avatar
ScottieJ
The Boss
The Boss
Posts: 11620
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: rotten sills

Post by ScottieJ » Thu Sep 25, 2014 9:39 am

If you decide to go with box section sills I wouldn't go for anything thicker than 3mm ideally. I just used 90x90x3.6 I think for Johns.
Image


Personally I prefer to rebuild the sills out of 1.2mm sheet on mine, welding on box section sills isn't the nicest of jobs.
Image

Image
Zuki Build

Steady as she goes!
Top
kevin9044
Got muddy boots
Got muddy boots
Posts: 33
Joined: Thu Sep 11, 2014 1:05 pm

Re: rotten sills

Post by kevin9044 » Fri Sep 26, 2014 8:34 pm

They look good scottiej. Im a bit overwelmed with it all. Im trying to do one bit at a time but i keep seeing everything else!! Definitely prefer the box section but it does seem to be a lot of agro!!
Top
User avatar
twiss
SCUK Computer Wizard
SCUK Computer Wizard
Posts: 6110
Joined: Mon Nov 08, 2010 2:28 pm
Location: Birkirkara, Malta
Contact:
Contact twiss

Re: rotten sills

Post by twiss » Mon Sep 29, 2014 4:18 pm

People have done some pretty tidy tube sills in the past as well
Twiss

'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410

"If brute force doesn't fix your problem, you aren't using enough of it."
Top
User avatar
ferris
Suzuki Guru
Suzuki Guru
Posts: 1226
Joined: Thu Jul 23, 2009 3:55 pm
Location: Bristol

Re: rotten sills

Post by ferris » Mon Sep 29, 2014 5:54 pm

Box section sill are relatively straight forward as body work go's. When i did mine it was the first time i had welded anything ever! I used 90x90 box section.

Image
Image
Image
86 SJ413 tin top, 1.6 8v, SU carb, YJ spring conversion, virtual lift, 33x12.5x15 KL71's, rocklobster, rear discs, power steering.
Top
Post Reply

Return to “Bodywork, Paint and Interior Trim”