G box to Pug 1.9TD enigne?

Starts at the flywheel, ends at the hubs, any problems along them lines, ask your questions here.
User avatar
d_r_1989
Winching along now
Winching along now
Posts: 523
Joined: Tue Jul 08, 2014 1:49 pm
Location: Halifax west Yorkshire

Re: G box to Pug 1.9TD enigne?

Post by d_r_1989 » Sat Jan 03, 2015 11:50 pm

Yep that was me, not been on there for a loooooong time! Seems dead compared to this forum! Ill be changing it in a couple of weeks time. Once i get all thd rest of my million jobs done! It drives quite well to bd honest, gears seem to be suited for it. When i had thd samurai transfer box and samurai diffs it was happy on the motorway, now its not so much but i have changed the transfer box for a 410 and using sj413 diffs. Still does over 70 now and happily sits at 50.

Anton i dont think iv actually made a build thread! I best get one made and back dated with pics.

Anton
I spend far too much time on here
I spend far too much time on here
Posts: 3859
Joined: Tue Jan 12, 2010 12:12 pm
Location: London

Re: G box to Pug 1.9TD enigne?

Post by Anton » Sun Jan 04, 2015 12:28 am

d_r_1989 wrote:Anton i dont think iv actually made a build thread! I best get one made and back dated with pics.
:doublethumbs:
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!

My: Build thread To-do list Pay and Play map

User avatar
waynesworld
Got muddy boots
Got muddy boots
Posts: 56
Joined: Wed Oct 16, 2013 4:07 pm

Re: G box to Pug 1.9TD enigne?

Post by waynesworld » Wed Jan 07, 2015 10:50 am

So which Vit gear box ( bell housing really ) can i use with the Pug 1.9 TD engine, I see the commercial will go but they had the XUD 1.9 N/A ?

What i am getting at, will both diesel Vit bell housings take the XUD 1.9 TD enigne.?

Mite of found one and need to make sure its the correct one for the engine.

User avatar
d_r_1989
Winching along now
Winching along now
Posts: 523
Joined: Tue Jul 08, 2014 1:49 pm
Location: Halifax west Yorkshire

Re: G box to Pug 1.9TD enigne?

Post by d_r_1989 » Wed Jan 07, 2015 8:51 pm

Commercials are turbo just very very slow. Don't think estates will as they were Mazda engines I believe. To tell if it's xud it will have starter motor on top passenger side, so top right of gbox if your looking straight on.

User avatar
waynesworld
Got muddy boots
Got muddy boots
Posts: 56
Joined: Wed Oct 16, 2013 4:07 pm

Re: G box to Pug 1.9TD enigne?

Post by waynesworld » Wed Jan 07, 2015 10:23 pm

Do the 1.9 vit/pug engine comes as called a HDi aswell.

just a quick look on Wiki, they didnt do a 1.9HDi.

User avatar
d_r_1989
Winching along now
Winching along now
Posts: 523
Joined: Tue Jul 08, 2014 1:49 pm
Location: Halifax west Yorkshire

Re: G box to Pug 1.9TD enigne?

Post by d_r_1989 » Wed Jan 07, 2015 10:47 pm

Pug hdmi has same bell housing but pretty sure they didn't do a hdi suzuki.

User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: G box to Pug 1.9TD enigne?

Post by ROBBIE » Sat Jan 17, 2015 11:01 am

Dont know if you know already, but waste veg and hdi don't mix
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good

Anton
I spend far too much time on here
I spend far too much time on here
Posts: 3859
Joined: Tue Jan 12, 2010 12:12 pm
Location: London

Re: G box to Pug 1.9TD enigne?

Post by Anton » Sat Jan 17, 2015 12:34 pm

They do if you *carefully* make the waste veg into biodiesel.

You have to do it carefully, not just dump lye into it and stir - you have to balance the PH levels so that it's not acidic or alkaline, and then it should be ok to run through your fuel tank.

Still, it's a lot more work than just straining it through an old sock and dumping it in your fuel tank!

:hahaha:
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!

My: Build thread To-do list Pay and Play map

User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: G box to Pug 1.9TD enigne?

Post by ROBBIE » Sat Jan 17, 2015 2:23 pm

When I was running my old xud pug I had a shed just big enough to have a settle tank and a few 20ltr pots so no chance of bio for me, that and I was too lazy :lol: So when we got a hdi I still tried wvo, and it all got messy :oops:
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good

User avatar
waynesworld
Got muddy boots
Got muddy boots
Posts: 56
Joined: Wed Oct 16, 2013 4:07 pm

Re: G box to Pug 1.9TD enigne?

Post by waynesworld » Tue Jan 20, 2015 8:12 pm

I used to run WVO in my 28.TD shoggy, filter to 1mic then just just dump in the tank or 50/50 if below 5degC ambient temp, this will also work i believe on a HDi but only on a twin tank set up.
A bit of hassle but whe i was getting good used veg oil at 25pl it was worth it.

Post Reply