Suzuki sj 410 from Cornwall PROJECT Never Ending Project
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
Yep ok I will just bolt them on how they are
I.just can't wait.to fit them but I ain't got much.time on the evenings as I need it to get to work and college
I.just can't wait.to fit them but I ain't got much.time on the evenings as I need it to get to work and college
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
wheel bearing is gone in the rear axle
But I have fitted the new springs and tadah they are 1.5-2 iinches higher than.my old ones
But I have fitted the new springs and tadah they are 1.5-2 iinches higher than.my old ones
- Attachments
-
- IMAG0246.jpg (1.49 MiB) Viewed 5929 times
-
- IMAG0249.jpg (1.76 MiB) Viewed 5929 times
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
- suzukisteve
- Suzuki Guru
- Posts: 1344
- Joined: Sat Feb 04, 2012 10:07 am
- Location: Christchurch, Dorset
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
lookin good dude, where did you get em from?
rear bearings are easy to get hold of and not to bad to fir either
rear bearings are easy to get hold of and not to bad to fir either
pickle power!
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
Are all 410 bearings the same as I have a Spanish 410 rear axle on my zook
Got them of eBay http://www.ebay.co.uk/itm/SUZUKI-SJ410- ... 0850654254
The hardest bit is getting the shaft out I had a spare axle so I thought I would take that one out and that one was easy but the shaft in my zook is stuck in.there
Got them of eBay http://www.ebay.co.uk/itm/SUZUKI-SJ410- ... 0850654254
The hardest bit is getting the shaft out I had a spare axle so I thought I would take that one out and that one was easy but the shaft in my zook is stuck in.there
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
- suzukisteve
- Suzuki Guru
- Posts: 1344
- Joined: Sat Feb 04, 2012 10:07 am
- Location: Christchurch, Dorset
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
can you use a slide hammer of the like on it? might give it enuf force to get it to move mate.
you gonna do a ruf then?
you gonna do a ruf then?
pickle power!
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
I plan to do ruf in a coupe of mounts but funds is getting a bitblow so can't for a while
I bolted a pice of angle metal on too 2 the Drum nuts and I put a car sissor jack in bertween the spring.and the angle metal and all it is doing is bending the meatal I gave up for the day about 2 hours ago but I.will have a better go tmoz
What do I need to get to do the rear wheel bearing
Wheel bearing
Spacer
Oil seal
I bolted a pice of angle metal on too 2 the Drum nuts and I put a car sissor jack in bertween the spring.and the angle metal and all it is doing is bending the meatal I gave up for the day about 2 hours ago but I.will have a better go tmoz
What do I need to get to do the rear wheel bearing
Wheel bearing
Spacer
Oil seal
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
- suzukisteve
- Suzuki Guru
- Posts: 1344
- Joined: Sat Feb 04, 2012 10:07 am
- Location: Christchurch, Dorset
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
if you buy a bearing kit it should have everything you need in it. gimme a sec and ill find a part number
pickle power!
- suzukisteve
- Suzuki Guru
- Posts: 1344
- Joined: Sat Feb 04, 2012 10:07 am
- Location: Christchurch, Dorset
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
here we go: adk88204 or brt973
should be able to get either from most factors
should be able to get either from most factors
pickle power!
- Darrell
- Suzuki, will you marry me?
- Posts: 2988
- Joined: Wed Feb 23, 2011 7:54 pm
- Location: south oxfordshire
- Contact:
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
A new retaining collar, often part of a kit!dazerede wrote:I plan to do ruf in a couple of mounts but funds is getting a bit low so can't for a while
I bolted a piece of angle metal on too 2 the Drum nuts and I put a car scissor jack in between the spring.and the angle metal and all it is doing is bending the meatal I gave up for the day about 2 hours ago but I.will have a better go tmoz
What do I need to get to do the rear wheel bearing
Wheel bearing
Spacer
Oil seal
Maybe a brake pipe spanner, unless your backplate has the section that comes out.
A ordinary spanner may do, but once the nut is rounded off its a pain.
A angle grinder.
Access to to press.
- Attachments
-
- mHX1oYyTNWl3xSJKj5t0deg.jpg (6.8 KiB) Viewed 5898 times
-
- Rear wheel bearing diagram.jpg (365.94 KiB) Viewed 5898 times
2005-GV 1600se, "Hell" What do I know!
- dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: Suzuki sj 410 from Cornwall PROJECT Never Ending Project
Right I give up
I have tried it this way and no luck my other shaft came out piece of piss a while back using it this way I just don't understand Chears Darrel I might aswell buy 2 kits just incase my other bearing goes in my rear axle
I have tried it this way and no luck my other shaft came out piece of piss a while back using it this way I just don't understand Chears Darrel I might aswell buy 2 kits just incase my other bearing goes in my rear axle
- Attachments
-
- IMAG0250.jpg (1.7 MiB) Viewed 5885 times
-
- IMAG0251.jpg (1.45 MiB) Viewed 5885 times
-
- IMAG0252.jpg (1.65 MiB) Viewed 5885 times
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT