Presume the tickover not being able to drop below 1200 isn't linked to cable tension?
Should be pretty easy to tune.
Anton's build
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Anton's build
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
No, I have my cable tension set a little lose. I think it's somewhere between the throttle disc spring valve (gotta look into that one, Chris) the timing, and how I've set (mis-set?) the needle.
Gonna start by doing the timing, then try resetting the needle, then looking into the throttle disc spring issues.
Might do all of that in the car park if they'll let me, and then see if they'll run it up on the emissions machine for me again while I mess with the mixture screw.
Gonna start by doing the timing, then try resetting the needle, then looking into the throttle disc spring issues.
Might do all of that in the car park if they'll let me, and then see if they'll run it up on the emissions machine for me again while I mess with the mixture screw.
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
See the black rubber hose there, connected to the little green thing sticking out of the top of the carb - that's my vac advance. It was a hole that went into the carb in front of the throttle disc, and was just going to atmosphere.
I used it for my vac advance instead of drilling a new hole, because I assumed that it wasn't supposed to be unblocked.
Now I'm wondering if I've done something stupid, and I need to unblock that hole and drill a new one for the dizzy vac advance line.
Last edited by Anton on Sun Jul 16, 2017 9:19 pm, edited 2 times in total.
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Anton's build
Advance should be carb side of the butterfly.
Tune it using the John twist video on YouTube.
Tune it using the John twist video on YouTube.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
Dan - the advance is taken from between the venturi and the butterfly.
I used this video (and a description of the process given to me by Scottie) to try to tune the carb.
I was still up at 6.3 (gotta get below 4.5). Everything else is sorted. Hydrocarbons were low (700 out of 1200) but CO was way high.
Not sure what causes high CO - running rich should bump the HC levels, not the CO levels, shouldn't it? I have no idea how to get these emissions down, I'm just going to have to get a gas analyser and then play with it until I reach a setting that actually works.
I'm a bit worried now that I'm burning oil, actually.
I used this video (and a description of the process given to me by Scottie) to try to tune the carb.
I was still up at 6.3 (gotta get below 4.5). Everything else is sorted. Hydrocarbons were low (700 out of 1200) but CO was way high.
Not sure what causes high CO - running rich should bump the HC levels, not the CO levels, shouldn't it? I have no idea how to get these emissions down, I'm just going to have to get a gas analyser and then play with it until I reach a setting that actually works.
I'm a bit worried now that I'm burning oil, actually.
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
twiss
- SCUK Computer Wizard
- Posts: 6110
- Joined: Mon Nov 08, 2010 2:28 pm
- Location: Birkirkara, Malta
- Contact:
Re: Anton's build
Might be worth disconnecting the vac advance for the emissions tuning?
Should run just as well with static timing? and you only need to do the idle emissions test I think...
(jammy bastard)
Should run just as well with static timing? and you only need to do the idle emissions test I think...
(jammy bastard)
Twiss
'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410
"If brute force doesn't fix your problem, you aren't using enough of it."
'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410
"If brute force doesn't fix your problem, you aren't using enough of it."
Re: Anton's build
Running rich will bump the CO levels up, has the carb been rebuilt? Could be the choke I rings are allowing fuel through.
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
My HC levels are low (700 out of 1200, if memory serves) so I'm worried that I'm burning oil or something.
I've got a gunson gastester coming now. Plan is to hook it up, do the timing, set up the carb, and all being well, pass emissions.
Other tricks I might try are:
Anyhow, he's passing the gastester onto his mate who works just across the river. Hoping I can pop over and pick it up on Tuesday.
Should have a much better idea of what's going on then.
I've got a gunson gastester coming now. Plan is to hook it up, do the timing, set up the carb, and all being well, pass emissions.
Other tricks I might try are:
- Redex the crap out of it
- A tiny teeny weeny bit of water sprayed into the carb while it's running (to decoke)
- "Italian tuneup"
- Run oil cleaner through and new oil
- Rebuild the carb with new seals
Anyhow, he's passing the gastester onto his mate who works just across the river. Hoping I can pop over and pick it up on Tuesday.
Should have a much better idea of what's going on then.
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
It's taxed, MOT'd and insured.
But the battery is dead, so I have to charge it up before I can go anywhere in it...
Still, tomorrow might be fun!
Last edited by Anton on Sun Jul 16, 2017 9:20 pm, edited 2 times in total.
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
ROBBIE
- I spend far too much time on here
- Posts: 4555
- Joined: Tue Sep 09, 2008 6:32 pm
- Location: Dorset or stuck
Re: Anton's build
well done dudeSid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Jimny 1.6 not as good as an SJ but still good